4- A two-phase servomotor has 115/0°V applied to the main winding. At a particularpoint of operation corresponding to a control winding voltage of 75Z-80°V, thepositive and negative-sequence impedances are 220/67° and 175/57°0respectively.a- Determine the positive and negative sequence components of the main and controlwinding currents.b- Find the total values of the main and control winding currents.

Answered: Image /qna-images/answer/ecd97a12-88a3-43ba-b759-d287fcaaa174.jpg

4- A two-phase servomotor has 11520°V applied to the main winding. At a particular point of operation corresponding to a control winding voltage of 75Z-80°V, the positive and negative-sequence impedances are 220/67°2 and 175257°0 respectively. a- Determine the positive and negative sequence components of the main and control winding currents. b- Find the total values of the main and control winding currents

4- A two-phase servomotor has 11520°V applied to the main winding. At a particular point of operation corresponding to a control winding voltage of 75Z-80°V, the positive and negative-sequence impedances are 220/67°2 and 175257°0 respectively. a- Determine the positive and negative sequence components of the main and control winding currents. b- Find the total values of the main and control winding currents

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In general, which of the following is/are a factor that will determine the synchronous speed of a 3-phase motor? 4. a) frequency b) number of stator poles per phase c) both "a" and "b" d) neither "a" nor "b"
For the design we assuming following parameters 1) winding : Lap 2) simplex 3) Number of slots : 16 , single turn coil with 2 conductors per slot 4) Number of poles = 4
A) Adding resistive loads in parallel to the output terminals of a series connected DC generator will the total load resistance. a) increase b) decrease c) either "a" or "b" d) neither "a" nor "b" B) Adding resistive loads in parallel to the output terminals of a series connected DC generator will the current through the field winding. a) increase b) decrease c) either "a" or "b" d) neither "a" nor "b"
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux C) Total flux B) Mutual flux D) Leakage flux 5. The ------- are represented in the induction motor equivalent circuit by the resistor Rc (or the conductance Gc). A) Stray losses. C) Air-gap losses B) Friction and windage losses D) Core losses 6. The per-phase voltage Vo can be calculated by dividing the total voltage on. A) √3 B) √1.404. C) √0.707. D) √2.
the single-phase ac voltage controller has a 240 V rms 50 Hz source. The load resistance is 20002 and the delay angle is 30º. Determine (a) the rms load current, (c) the power output (b) the power factor.
The reactance's of the alternator during the periods of steady state are given bellow, Leakage reactance(X)=0.18 ohm, and armature reactance (Xad) = 0.67 ohm. The value of the syncronous reactance during the steay state conditions is Syncronous Reactance in ohm
Q5)A- A 3-phase Induction motor has an efficiency of 0.91 when it delivers an Output power of 22KW. At this load,the stator copper losses equals the rotor copper losses and the total copper losses equals the no- load losses the mechanical losses are one-fourth the no-load losses Find the slip write equations with drawing power flow Diagram ? B-Define the following: (i)Regulation (ii) Slip (iii)Core and shell Transformer (iv)PM motor
Three phase slip ring induction motor gives a reading of 65 V across slip rings when at rest with normal stator voltage applied. The rotor is star connected and has an impedance of (0.8 + j6) ohm per phase. Find the rotor current when the machine is (i) at standstill with the slip rings joined to a star-connected starter with a phase impedance of (4+j3) ohms and (ii) running normally with a 5% slip.
Choose the correct option does not have self-starting torque DC Motor EMF due to Mutual inductance Choose... DC Motor Generated EMF DC Generator Back EMF Transformer EMF due to rotating magnetic field Single phase system Three phase induction motor
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
The shunt field winding of a shunt generator has a resistance of 80ohms at 20 degrees Celsius. After several hours of continuous operation, the winding temperature rises to 50 degrees Celsius. How much is the winding resistance under this condition. Assume the resistance temperature coefficient of copper to be 0.004 ohm per degree at 0 degree Celsius. *
What type of power losses does windage lods, bearing and brush friction is consid3red? a. stray losses b. armature losses c. core losses d. copper losses