4-A thyristor of thermal resistance 1.8 C°/W is mounted on a heat sink of thermal resistance 2.0 C/W. The maximum power loss of the thyristor if the junction temperature is not to exceed 125C' in an ambient of 40 C° is: 22.3W 50.8W 30.9W 5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V

4-A thyristor of thermal resistance 1.8 C°/W is mounted on a heat sink of thermal resistance 2.0 C/W. The maximum power loss of the thyristor if the junction temperature is not to exceed 125C' in an ambient of 40 C° is: 22.3W 50.8W 30.9W 5-For single phase half-wave controlled rectifier with a freewheeling diode connected across the inductive load, the supply voltage is 220V (RMS). The mean value of the output voltage for a=45 is: 100.7V 70.9V 84.5V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is a zener diode? Draw the I - V characteristics of a zener diode and explain how it is different from a normal diode?
Can this question be solved as soon as possible?Or a maximum of 10 minutes
Explain the difference between Homojunction and Double Hetero junction Light emitting diodes with their structural diagram
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Find the applied voltage on a forward biased diode if the current is 1mA and reverse saturation current is 10-10. Temperature is 25°C and takes ideality factor as 1.5.
Calculate the reverse saturation current of a diode if the current at 0.2V forward bias is 0.1mA at a temperature of 25°C and the ideality factor is 1.5.
Calculate the reverse saturation current of a diode if the current at 0.2V forward bias is 0.1mA at a temperature of 25°C and the ideality factor is 1.5.
Maximum voltage applied at single phase full wave rectifier diode is 440 Volt. load is resistive find value of average output voltage and rms output voltage.
N H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr 150usec and the source voltage Vs = 200V at frequency = 5 kHz. Calculate the average output voltage. IC L.C. the HoNo locor
d. Clamper. Show the output waveform of the clamping circuit with input given using ideal diode. f = 1000 Hz 10 C = 1 µF 12 13 Vi R 100 k2 -SV -20
In the following circuit, Vin is a sinusoid AC input voltage which has a 5. peak voltage of 15v. Zener diode D has a Zener voltage of 10V. Sketch the waveform of Vout. Hint: Consider when Zener diode is forward and reverse biased. R 1ka Vin Vout
There are two LEDs that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the “on” diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V