4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the loads as shown in the figure. Determine the shear stress at the glued section of the beam. 500 N/m 300 N/m A B 3m 0

4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the loads as shown in the figure. Determine the shear stress at the glued section of the beam. 500 N/m 300 N/m A B 3m 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam AB is loaded as shown in the Cross-section of the beam figure and the beam is supported with a cable BD. The beam's cross-section is rectangular as shown. It is known that the tension force in cable BD is 10.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 10cm 10cm +15cm+ 75cm B F-13.99KN 30cm 60cm 90cm
Flexure stress *Please answer in complete solution and draw the shear and moment diagram, Solve the Area moment of inertia*
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
Consider that a box section is used for the beam loaded as shown in figure. Using flexure and shear stress formula, determine the following Use a = 6 m, b = 3m, c= 344 mm, d = 51mm Distance of the centroid to the outermost fiber of the beam in mm.
Pls solve it
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
Calculate the moment of Resistance of the given beams. If the maximum stress is 100 N/mm2. 190 |不 15 (i) 550 k10> (all dimensions in mm)
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
The picture is in the picture. Thanks
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
Beam AB is supported as shown in the figure. Tie rod (1) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A, B, and C each have an ultimate shear strength of 57 ksi, and tie rod (1) has a yield strength of 33 ksi. A concentrated load of P = 14 kips is applied to the beam as shown. A factor of safety of 2.4 is required for all components. Determine: (a) the minimum required diameter for tie rod (1). (b) the minimum required diameter for the double shear pins at B and C. (c) the minimum required diameter for the single shear pin at A. 6.7 8 in. 3.8ft (2) 8.5ft
Calculate the design moment strength Mu for the following section. Take f'c = 40 MPa. Sketch the strain and stress distribution diagrams for each section and try to work out your solutions using equilibrium conditions. Yield stress for N bars is 500 MPa. 75 700 60 1500 T 4N28 450