4- A hair dryer is basically a duct in which a few layers of electric resistors are placed. A small fan pulls the air in and forces it to flow over the resistors where it is heated. Air enters a 1200-W hair dryer at 100 kPa and 22°C, and leaves at 47°C. The cross-sectional area of the hair dryer at the exit is 60 cm. Neglecting the power consumed by the fan and the heat losses through the walls of the hair dryer, determine (a) the volume flow rate of air at the inlet and (b) the velocity of the air at the exit. T = 47°C A,= 60 cm² P, = 100 kPa T = 22°C W, = 1200 W

4- A hair dryer is basically a duct in which a few layers of electric resistors are placed. A small fan pulls the air in and forces it to flow over the resistors where it is heated. Air enters a 1200-W hair dryer at 100 kPa and 22°C, and leaves at 47°C. The cross-sectional area of the hair dryer at the exit is 60 cm. Neglecting the power consumed by the fan and the heat losses through the walls of the hair dryer, determine (a) the volume flow rate of air at the inlet and (b) the velocity of the air at the exit. T = 47°C A,= 60 cm² P, = 100 kPa T = 22°C W, = 1200 W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A-C line Liquid R-134a A rigid container containing 6.6 kg of saturated liquid R-134a at 24°C is used to fill an air-conditioning system. A valve is opened and allows liquid R-134a to escape the tank into the A-C line until only 0.49 kg of R-134a remains in the tank, at which point the valve is closed. During the process, heat transfer is allowed to occur to maintain the tank temperature at 24°C. What is the quality of the refrigerant inside the tank at the end of the process? What is the total heat transfer for this process? KJ
Air at a rate of 50 m3/min enters an adiabatic compressor at a pressure of 100 kPa and a temperature of 24.3 C and exits at 500 kPa and 189.55 C. It then enters an insulated heat exchanger where it gets cooled by water. The air exits the heat exchanger at a temperature of 57.35 C. Water enters the heat exchanger at 20 C and exits at 50 C. Calculate the compressor power in kW, the mass for rate of the cooling water in kg/sec, and the rate of entropy generation for the compressor and the heat exchanger. Assume a mean heat capacity of water at ?? = 4.18 ??/???. You may also assume that there is no pressure drop in the heat exchanger)
Air is compressed in a two-stage , double-acting compressor which is electrically driven at 165 rpm. The low pressure cylinder (30.5 x 35.5-cm) receives 6.85 m3/min of air at 96.53 kPaa, 43.3°C, and the high pressure cylinder (20.3 x 35.5-cm) discharges the air at 717.06 kPa. Piston rods are 5.1 cm in diameter and the isothermal overall efficiency is 74%. Find (a) the volumetric efficiency, (b) the power of the driving motor.
During a reversible process executed by a non-flow system, the pressure increases from 50 psia to 200 psia in accordance with pV = C, and the internal energy increases 21.4 Btu; the initial volume is V1 = 3 ft3. Find the heat. Answer: -17 Btu
1) Refrigerant-134a enters the evaporator at 200 kPa with a quality of 45 percent and it leaves at 200 kPa and 10°C in a refrigerator. The refrigeration load is 500 W and COP of the refrigerator is 1.5, determine a- The compressor work b- The mass flow rate of the refrigerant c- The rate of heat rejected to the environment(
A centrifugal compressor pumps 45.3 kg/min of air at 101.32kPa and 15.6°C to 345 kPa and 132°C by an irreversible process. The temperature rise of 22.1 kg/ min of circulating water about the casing is 6.7°C. What is the horse power required? Neglect kinetic energy changes and no heat loss to surroundings.
A power plant,having a Carnot efficiency, produces 1.00GW of electrical power from turbines that take in steam at 500K and reject water at 300K into a flowing river. the water downstream is warmer by delta T due to the output of the power plant. Determine the flow rate of the river.
Heat is rejected from the condenser of a heat pump cycle by refrigerant-134a entering at 700 kPa and 50 ◦C at a rate of 105 kg/h and leaves as a saturated liquid. Determine (a) the temperature of R-134a at the condenser exit, (b) the volume flow rate at the exit of the condenser in L/min, (c) the COP of the heat pump if the rate of heat absorbed in the evaporator is 12,000 Btu/h.
NEED ASAP A compressor draws in 0.5 kgm/s of air with 7 m/s speed, 100 kPa pressure, and 0.95 m3/kgm. The air leaves at 5 m/s, 700 kPa and 0.19 m3/kgm. The internal energy of the air leaving is 90 kJ/kgm greater than that of the air entering. The coolant absorbs heat from the air at the rate of 58 kW. Determine the work in kW. Show given, formula and step by step solution. Kindly box every answer to the process. My prof said it can be 5 or more step to get the answer. Thanks. (No shortcut to get the final answer pls just step by step process to get the final answer) Will thumbs up after. Have a great day tutor.