4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI = 300.65 kNm², determine the value of maximum deflection in millimeters. 4m 4B 180 N-m 2m 10 N/m

Q: 30 kN 20 kN/m 2 m -3m 2. If the size of beam in Problem I is 150mm x 300mm and E = 15 GPa, what is…

A: E=15GPa

Q: the Virtual Work method to calculate the vertical deflection at A of the frame shown in Figure 2…

A: Given:- E= 200 GPaI = 250 × 10^6mm4 To find:-  vertical deflection at A

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A: Given data  2.7 KNm = 2700 Nm Find elastic curve equation, slope at point-B and deflection at…

Q: A cantilever beam is loaded as shown in the figure. Assume El is constant. Determine the deflection…

A:

Q: on at the free end. See figure 06. El = 1600NM² 6m Figure 06 c0m F0m

A:

Q: For the shown beam, calculate the deflection as well as the slope at point (e). EI is constant. 100…

A: Given data:- Beam diagram show in figure;

Q: find the value of deflection at the Position midway between the supports and at the overhanging end…

A:

Q: 120 kN 120 kN L-15 m El = constant E- 30 GPa The beam has a self weight of 5 kN/m in addition to the…

A:

Q: 4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI =…

A:

Q: Use the virtual work method to determine the vertical deflection at joint B of the frame show

A: A frame is given as shown in the figure above and it has been asked in the question to determine the…

Q: Q8. Determine the deflection of point B on the steel beam with 1 = 80x106 mm4 and E = 200 GPa. [Ans.…

A: Given data: I=80×106 mm4E=200 GPa

Q: 200 KN 100 KN C Sm + + 5mt 10m- 2エ

A:

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A:

Q: The quadrantal ring, as shown in the figure below, is of radius 2 m. It supports a concentrated load…

A: Consider the given figure. Since no horizontal load at A is acting so introduce a dummy load F.…

Q: b) Determine the deflection at the free end of the beam shown in figure 2b) using the conjugate beam…

A:

Q: A simply supported beam carries a load as shown in the figure below. What is the value of deflection…

A:

Q: A cantilever beam supports a uniformly varying shown in the figure. If EI = 300.65 kN - m², detern…

A:

Q: . For the beam loaded as shown in the figure below, determine the following unknowns using any…

A:

Q: A 10-m long simple beam carries a load that varies uniformly from zero at the left support to 12KN/m…

A:

Q: . For the beam loaded as shown in the figure below, determine the following unknowns using a…

A:

Q: using the moment area theorems determine the deflection at point B.

A: ###Calculation of deflection at B using Area Moment Diagram

Q: in mm ) Solue for the deflectiom e the miáspan using vwM lookN 20 kal /m E = 2006 Pa Cross section…

A:

Q: Use any geometric method to solve the response of the bean, Determine the maximum deflection (in mm)…

A:

Q: A 3m-

A:

Q: QUESTION 1 A built-in beam shown in Figure 1 carries a distributed load of 30 KN/m between point A…

A:

Q: Determine the maximum deflection of the beams given below using Area-Moment Method.

A: Given Data  E = 70 GPa  I = 500 × 106 mm4  Determine the maximum deflection of the beam using Area…

Q: 5: Find the deflection at b, c and d for the loaded beam shown in the figure below by using finite…

A:

Q: 20kN/m 20kN/m 1m 2m 1m 1m 5m

A: A loaded beam is given and it has been asked to determine deflection at F using virtual work method.…

Q: 60 kN 32 kN / m C EI 1.2 El 4 m 2 m 2m

A:

Q: Determine the value of the deflection at C in mm. Answer in 2 decimals 6kN 4KN By E = 200,000 MPa I…

A:

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A:

Q: The 9m beam in figure 05 is loaded as shown. The location of maximum deflection measured from the…

A:

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A:

Q: 50 kN w = 20KN/m C A 4m B 4m RA REAL BEAM Re M1 R1 R2 M2! CONJUGATE BEAM

A:

Q: 4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI =…

A: Given data  EI = 300.65 KNm2

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.