*4-88. If the allowable normal stress for the bar is 120 MPa, determine the maximum axial force P that can be applied to the bar. O allow

Q: The armor shown supports a pedestrian bridge between two buildings that it exercises vertical…

A: To determine the axial force in member BC of the given truss.   In the method of section, a…

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The di Lanath…

A:

Q: The three-member truss is used to support vertical load P. If P=200 kN, find the stress of members…

A:

Q: 4. A compound beam is made of two beams, AC and CD, connected by a hinge at C. Beam AC is 20 feet…

A: Solution Draw the Diagram

Q: *9-8. Determine the force in the spring. Assume the support at A is fixed. The beam has a width of 5…

A:

Q: The force of a Truss is as follows. The E of all member sections is 30000 kips\in^2, and the A of…

A:

Q: 2KN 0,7kN 0,3KN 0,5tf M G 8 x (a)m

A: Given Data: a=1.1 m p=1 kN big vertical member is 2m Small vertical member is 1m

Q: A wooden beam is fabricated from three boards, which are fastened together with screws, as shown.…

A: An object's bending stress is its normal stress when subjected to external loads at any…

Q: The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid…

A: Given Load PSpan 12 ftTo find out Normal stress in CG

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: Find the moment capacity MR = M, of a beam with: %3D b = 20 in %3D h = 34 in 8- #7 bars # 4 stirrups…

A:

Q: The shäft iš made portion made of steel and having a brass core. If it is fixed to a rigid support…

A:

Q: The force on the triangular plate that is submerged in water as shown below waters surface 6m 4m is…

A:

Q: kN , and the maximum allowable compressive force is (Fc)max = 3 kN. Take d = 2 m* Determine the…

A:

Q: A cantilever truss is pin-connected at joint D and is supported by a roller at G. Spacing of trusses…

A: Since it is said that wind load is normal in front  A,B,C,D So , take the plane passing A,B,C,D  as…

Q: G5 // The bar AB is considered to be absolutely rigid and is horizontal before the load of 10000N is…

A:

Q: An assembly of bars are designed in Figure 1: The assembly is made of structural A-36 steel where…

A:

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD 2- if Beam Weighs is not know then finding of…

Q: Select member FC and CB in the truss to carry the inclined force P. Set the allowable tensile ress…

A:

Q: Q2) ACED frame is pinned at C and support by two identical wires at A and B. The two wires have…

A: Given ACDE frame E=70 GPaA=250 mm2=250×10-6 m2α=23×10-6 1/C

Q: For the given cross section, determine the torsional and warping constant with the given parameters.…

A: Solution: The bending resistance formula is given by the equation:  θ=TL/GJ where  T = Torque (N·m…

Q: PROBLEM 2 (35%). Determine the maximum force (tension or compression) at member IH of a two-side…

A: There is a truss bridge with moving load T-U-U moving on it maximum force on member IH can be find…

Q: The cross sectional area of the bar ABCD is 545 mm2 F1 = 15 kN F2 = 20 kN F3 = 40 kN Determine the…

A: cross sectional area =545 mm2 F1 = 15 kNF2 = 20 kNF3 = 40 kN

Q: The working stresses are 120 MPa in tension and 90 MPa in compression. Determine the smallest safe…

A:

Q: The bridge truss shown carries the following uniform live load and concentrated live load. в с D A B…

A:

Q: F = 3.3 kN, a = 2.4 m, b 3 m, c= 2 m, and d = 2 m.

A:

Q: Situation 4: Given the truss shown, determine the maximum value of the downward force P if the…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 845 lb, a = 3.0 ft, b = 2.0 ft, r = 9 in.…

A: We have to find the value of magnitude of pin force at A. Given data is W = 845 lb, a = 3.0ft, b 2.0…

Q: 4m 60⁰ 2kN C 60⁰ 2kN B 8m 30⁰ 2kN A

A: Cut the x-x plane as shown in below solution. Applying equilibrium equation in both x and y…

Q: -4 m- B 60 E 60 D 4 m- 4 m- 'P

A: Given section: FBD:

Q: Abar AB is attached at A as fixed support. A small spaces can be seen on the other side of the bar…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in.…

A:

Q: *8-36 The frame supports a centrally applied distributed load of 1.8 kip/ft. Determine the state of…

A:

Q: 1. Given the values of the load L and dimension R, for what value of the couple M will the force in…

A:

Q: 10–25. Determine the force in each member of the truss. AE is constant. Show primary and secondary…

A: To Calculate-  force in each member of the truss.

Q: An unsymmetric moment of M = 5 kN.m is applied on the cross-section of an aluminum beam. Find the…

A:

Q: 3.9 kN 4.0 kN 2.0 m 2.0 m 1.1 m 2.2 m D E

A:

Q: If the load P on the beam below causes the end C to be displaced 10mm downward, determine the normal…

A:

Q: Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a…

A:

Q: 4 m B P₁ 4 m C₁ 4 m 6 m D

A: Identify the Reaction of Truss support  Apply Equilbrium Condition to get the Reaction. Then apply…