4-82. The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. If the two 304 stainless steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 12 MPa. 100 mm Probs. 4-81/82 150 mm

4-82. The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. If the two 304 stainless steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 12 MPa. 100 mm Probs. 4-81/82 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The brass wire has a triangular cross section, 2mm on a side. The yield stress for brass is Ty= 208 MPa. Gbr= 37 GPa. Determine the maximum torque to which it can be subjected so that the wire will not yield and the angle of twist
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
135 mm 85 mm σ, = -58 MPa E = 105 GPa D = 0.33 Beer & Johnston & DeWolf & Mazurek 2.86 (a) For the axial loading shown, determine the change in height and the change in volume of the brass cylinder shown. (b) Solve part a, assuming that the loading is hydrostatic with Ox= Oy = O₂ = -70 MPa
a steel tube sandwiched between two rods, one of aluminum and the other of bronze, and as shown in Fig. 110 - P. The axial loads indicated. Calculate the maximum value of P so that the stress does not exceed in aluminum, MPa 80, in steel 150 MPa, and in bronze 100 MPa.
Write complete solution
Aluminum Bronze Steel 2P 3P P 4P - - 1.0 m 0.8 m FIG. P2.16 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses pre- scribed in the table are not to be exceeded. A (mm²) E (GPa) G, (MPa) Вronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140
Given the compound bar below, determine the maximum allowable value of P if the change in length of the bar is limited to 5.67mm. The bar properties and allowable stresses are given in the table below. (answer in N)
(b) (ii) A 20 mm diameter rod made from 0.4% C steel is used to produce a steering rack. If the yield stress of the steel used is 350 MPa and a factor of safety of 2.5 is applied, what is the maximum working load that the rod can be subjected to? 2
Class work: The two solid cylindrical steel rods AB and BC are welded together at B and loaded as shown in the figure. Knowing that the normal stress must not exceed 175MPa in rod AB and 150MPa in rod BC determine the smallest allowable values of d, and d₂. استنساخ 200 m مكتب المدير مقابل كلية الهندسة مجمع فاطمة 250 mm B 40 kN - d 30 kN
The question is below.
The shaft system is made from aluminum and brass. -39 GPa) Aluminum (G=27 GPa) 1200 N The maximum shear stress tmax (MPa) in the shaft equals to: O675.45 Pc 1200 SL 90L PO
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >