4-75. Water flows into the tank through two pipes. At A the flow is 400 gal/h, and at B it is 200 gal /h when d = 6 in. Determine the rate at which the level of water is rising in the tank. There are 7.48 gal/ft'. -3 ft 8 in. Prob. 4-75

4-75. Water flows into the tank through two pipes. At A the flow is 400 gal/h, and at B it is 200 gal /h when d = 6 in. Determine the rate at which the level of water is rising in the tank. There are 7.48 gal/ft'. -3 ft 8 in. Prob. 4-75

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A centrifugal water pump has an impeller with r2=12 in., r1= 4 in., ẞ1 =20°, and ß2 = 10⁰. The…

A: r2 = 12 in r1 = 4 in N = 1800 rpm

Q: 9. Through inlet orifices, which are facing the direction of motion of the ship, the water from the…

A: To find: If the statement is true or false

Q: EXAMPLE 10.5. A pump delivers 2.5 cfs of 70°F water from a reservoir at elevation 50-ft to a…

Q: 4) The increase of temperature results in (a) increase in viscosity of gas (d) decrease in viscosity…

A: The Bernoulli equation states that, points 1 and 2 lie on a streamline, the fluid has constant…

Q: bject: Dete: he wat er level in a tank iS 20m above the giound. A hose is connected to the Dotton of…

A: Given data Depth of water Height of water jet To find Pump minimum pressure

Q: Water flows steadily with negligible viscous effects through the pipe shown in the figure below.…

A: Given: Required Diameter at outlet

Q: Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes.…

A: Q=300L/s To find Q2

Q: As shown in the figure below, the smaller pipe is cut off a short distance past the reducer so that…

Q: Q2) There is gate inclined by 50° that separates a fluid from water on the left. Calculate he volume…

A: Introduction- Atoms and molecules make up a fluid. The distance between molecules varies by orders…

Q: 5. Determine the velocity and pressure at sections 2 and 3 if the water flows steadily through the…

Q: water enter an inward flow turbine at an angle of 22° to the tangent to the outer rim and leaves the…

A: Given : Speed of the wheel = 300 rpm Velocity of flow = 3 m/s Diameter of inner turbine = 30 cm…

Q: For the parallel-pipe system of Fig. each pipe is cast iron, and the pressure drop P₁ P2 = 3…

Q: The Power (P) required to drive the pump depends upon the diameter (D), the angular velocity (0),…

Q: In Fig. all pipes are 8-cm-diameter cast iron. Determine the flow rate from reservoir (1) if valve C…

A: D = 8 cm or 0.08 m Kv = 0.5

Q: Two identical each cylinders with a mass of 50 Supported by the smooth C and D. A and kg are planes…

Q: A sprinkler with unequal arms issuing jets of area 0.8 cm² at each end and facing same direction…

Q: Q2) The speed at which the cylinder (D₂ = 100 mm) be pushed down into the cylindrical tank (D₁ = 120…

A: Given data:- D1=120 mmD2=100 mmV2=0.01 m/s

Q: Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes.…

A: From given figure of pipe system it is very clear that ; Pipe AB is the starting pipe and Pipe DE is…

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

A: Manometer is used to measure pressure at any point which is exerted by a gas or liquid under the…

Q: 100 mm 300 mm 60 mm 150 mm Water flows out of the pipe at B with a velocity of 10 m/s at atmosphere.…

A: (a) Control volume and free body diagram Control volume ids the one marked in the dashed orange…

Q: For system. If the pressure at Point A is go! Determine the pressures at Points B. Cand Din 个 дост…

Q: 10.83 The steel pipe shown carries water from the main pipe A to the reservoir and is 2 in. in…

Q: al pump has an impeller of 500 mm external diameter and 200 mm internal diameter. It runs at 1000…

A: Given:- D=500mm d=200mm runs at 1000 rpm angle= 30 degree radial velocity=2m/s To find"- (a) Angle…

Q: A siphon is used to drain out a tank of water as shown. The siphon is 3" in diameter and drains out…

A: Given:Diameter of siphon, D=3 inchNozzle diameter, d=2 inch

Q: For the piping system of Fig. all pipes are concrete with a rough of 0.04 inch. Neglecting minor los…

Q: at 200 rpm. The gui

Q: Water flows through a 90° bend in a horizontal plane as depicted in the figure.

Q: 2. The gate separating the water and gas is hinged at the top. The distance z is 12 ft. Determine th…

A: Given : Distance Z = 12 ft Determine the force that must be applied at the bottom of the gate for…

Q: Waters enter a pump through a 25 cm. dia. Pipe at 35Kpa. It leaves the pump at 140 kPa through a 15…

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

A: Rate of flow the rate at which a liquid or other substance passes through a channel or conduit. The…

Q: urrent Attempt in Progress A 1-m³ volume of water is contained in a rigid container. Estimate the…

Q: Water is flowing at the rate of 300 L/sec from A to E as shown. Assume f = 0.025 for all pipes.…

Q: Diameter= 6 in Diameter = 3in

Q: An empty water tank has a diameter, D=6ft, and height, H=10ft, an inlet valve with a diameter, din…

A: The water tank has a diameter D= 6ft height, H=10ft,inlet valve with a diameter d(in)=6”outlet valve…

Q: Three immiscible fluiids are contained in a tank: 1.0 m of water, 1.20 m of oil (s= 0.80) and air…

Q: Ex: (Single pipe with pump) Without g. P8.13R it is determined that the flowrate is too small.…

A: Single pipe with pump is given

Q: Water flows steadily with negligible viscous effects through the pipe shown in the figure below.…

Q: Coneider incompressible, frictionless flow of a fluld in a horizontal pipe. The pressure and…

Concept explainers

Friction

Friction is defined as the force that prevents any solid surface, any layer of fluid, or any kind of element or material from sliding.

Question

4-75. Water flows into the tank through two pipes. At A
the flow is 400 gal/h, and at B it is 200 gal /h when d = 6 in.
Determine the rate at which the level of water is rising in
the tank. There are 7.48 gal/ft'.
-3 ft
8 in.
Prob. 4-75

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

*6-8. The nozzle has a diameter of 40 mm. If it discharges water with a velocity of 20 m/s against the fixed blade, determine the force exerted by the water on the blade. The blade divides the water evenly in the vertical plane at an angle of 0 = 45°. 40 mm B
Fluid of mechanics
Fluiid mechanicx. hydraulics
Medium lubricating oil (sg-D0.85) is pumped through 360m of horizontal 75mm pipe at the rate of 3.14L/s. If the drop in pressure is 300kPa. Compute for the absolute viscosity in Ns/m2 of the oil. a. 0.311 b. 0.206 C. 0.504 d. 0.790
he 30o directional pressure pipe elbow in the vertical plane is 60 cm in diameter. from the elbowThe flow rate of the current passing is 1 m3/s. At the lower end (1) of the elbow, the pressure is 70 kPa and the ground level is 30 m, the upperAt the end of the section (2), the ground level is 31 m. The fluid is water (ρwater=1000 kg/m3), frictionless and incompressible.taking into account thata) Find the velocities in sections (1) and (2) and the pressure in section (2).b) The weight of the pipe at the elbow is 1400 N. In case the length between sections is 1.2 mIn order to keep the elbow stable, taking into account the mass of water in the elbow, in the vertical directionCalculate the force that must be applied.
Ans: -9 mm/s Problem 5-34 Fluid having sp. gr. 0.88 enters the cylindrical arrangement shown in Figure 5 -10 at section A, at 0.16 N/s. The 80-mm-diameter plates are 3 mm apart. Assuming steady flow, determine the average velocity at section A and at section B. Assume radial flow at B. Ans: v₁ = 1.47 m/s; v₂ = 2.46 cm/s 80 mm Ø 3 mm 4 mm Ø Figure 5-10 04/29/2022 08:33
Q6
Water (p = 1000 kg/m³) flows horizontally through a nozzle into the atmosphere under the conditions given below. (assume steady state flow). Nozzle Water 2 O A2, V₂, P₂ A₁, V₁, P₁ At inlet: A₁ = 10-3m²; V₁ = 2m/sec; P₁ = 3 x 105 Pa (gauge) At outlet: A₁ = 10-4 m²; P2 = Patm Determine the external horizontal force needed to keep the nozzle in place.
ANSWER ASAP THANKS
- Probl Water flows from a large open tank, through a valve and out a pipe to atmosphere. A-9 cm². Az = 11m. h₁ = 5V²/2g Find: I Discharge (Q=?) in pipe. Assumptions: a = 1.
Water is flowing steadily in a horizontal elbow and nozzle combination shown in the figure. The gage pressure at section (1) is 100 kPa with inlet velocity of 2 m/s. At section (2) the water exits to the atmosphere. Neglecting pipe weight, determine the magnitude and direction of the x and y components reaction forces exerted on the flanges to withstand this flow. 160 mm y section (2) 300 mm V1 -> section (1) P, = 100kPa V, = 2m/s
Qu: Calculate the magnitude 4 direction af force exerted on the three-quar ter cylinder (ABCD), shown in figure below, which is (3m) long perpendieular to the figue. Also prove that this force passes through paint O. Water 2 m B 0.6