4-71. A steel surveyor's tape is to be used to measure the length of a line. The tape has a rectangular cross section of 0.05 in. by 0.2 in. and a length of 100 ft when T = 60°F and the tension or pull on the tape is 20 lb. Determine the true length of the line if the tape shows the reading to be 463.25 ft when used with a pull of 35 lb at T2 = 90°F. The ground on which it is placed is flat. 9.60(10-6)/°F, E, = 29(10') ksi. %3D a st %3D P P. 0.2 in. 0.05 in. Prob. 4-71

4-71. A steel surveyor's tape is to be used to measure the length of a line. The tape has a rectangular cross section of 0.05 in. by 0.2 in. and a length of 100 ft when T = 60°F and the tension or pull on the tape is 20 lb. Determine the true length of the line if the tape shows the reading to be 463.25 ft when used with a pull of 35 lb at T2 = 90°F. The ground on which it is placed is flat. 9.60(10-6)/°F, E, = 29(10') ksi. %3D a st %3D P P. 0.2 in. 0.05 in. Prob. 4-71

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The 13-lb bar AE is suspended by a cable that passes over a 5-in.-radius drum. Vertical motion of end E of the bar is prevented by the two stops shown. The value of μs=0.30 between the cable and the drum. Mo A B C D W 5 in. 5 in. 3 in. E Determine the corresponding force exerted on end E of the bar. The corresponding force exerted on end E of the bar is 314.8 lb
Help me figure out the problem. Asking for the moment diagram? and then, Show the value of x knowing you have the shear diagram. Again find the moment diagram and the value of your x. Show complete solution and box the final answer and write on a paper.
please sir solve accurate and fast. ( of possible solve compyuterised) THANKS a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when supported throughout under a tension of 5kg. the modulus of elasticity is 2.1x10^6kg/cm. what tension is required to make the tape measure 30m when supposed only at the two ends?
A 30- m steel tape weighs 0.04 kg/m was used to measure a line and was recorded to be 155m. If a pull of 6kg is applied, determine the Corrected Length of the line.
solve for the 2nd table using the above values and bearing of AB. Also, draw the illustration for better understanding. PROVIDE DETAILED SOLUTIONS AND CORRECT ANSWERS. DO DOUBLE-CHECKING TO ENSURE THE BEARINGS ARE CORRECT. CHECK ALSO FOR THE CORRECTION, ADJ, LATS AND DEPATURE AND THEY SHOULD BE EQUAL TO 0.
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and B. (b) Draw the shear-force and bending-moment diagrams for the beam. (c) Determine the deflection in the middle of the span. Assume w = 11 kN, L = 7.4 m and El - 6.9 x 104 kN-m2 is constant for the beam. V. L.
Please answer asap I will give 2 upvotes
Solve correctly
A team of house builders went to the Lowe's in Bloomfield, CT and bought bags of Fastset Self Leveling concrete mixes. They built a simple concrete wall for modern looking house, but it is very unstable and temporarily held by two blue cables as shown below. y (a) A В E (b) C X. Da (c) Knowing that the dimensions are (a) 3.5 m, (b) 1.9 m, (c) 1.7 m, (d) 1.4 m, and the tension in cable BD is 600 N. Draw a free-body diagram. Determine the moment about point O of the force exerted by the cable at B.
Ex-6. A steel tape with a cross-sectional area of 0.039 cm²and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape is 2°C. The measured slope distance is recorded 381.615 m. What is the corrected horizontal distance? AMa
How you got there -9.76, Is there two equal or something? I can not put this right on the calculator.