*4-32. The column is constructed from high-strength concrete and four A-36 steel reinforcing rods. If it is subjected to an axial force of 800 kN, determine the required diameter of each rod so that one-fourth of the load is carried by the steel and three-fourths by the concrete. Est=200 GPa, Ec=25 GPa. 800 KN 300 mm 300 mm

*4-32. The column is constructed from high-strength concrete and four A-36 steel reinforcing rods. If it is subjected to an axial force of 800 kN, determine the required diameter of each rod so that one-fourth of the load is carried by the steel and three-fourths by the concrete. Est=200 GPa, Ec=25 GPa. 800 KN 300 mm 300 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar is made of a 2014-T6 aluminum alloy. Determine its smallest thickness b if its width is 5b. Assume that it is pin connected at its ends.
Determine the largest internal normal force in the bar.
The boom DF at the job crane and the column DE have a uniform weight of sw N/m. If the hoist and load weight P N, determine the resultant internal loading in the crane on cross-section through points A, B and C. h2 L1=1 m L2=2 m L3=1 m h1=1 m h2=1.3 m h1 P=540 N Sw=18 N/m D E B L1 L2 A L3 P F
SN = 79 kips
The bracket shown below is to carry a load F = 20 kN acting at an eccentricity of 1.2 from the centroid of four equal sized rivets. Determine the size (diameter) of the rivets if the shear stress in the rivets is not to exceed 50 MPa.
Determine the magnitude of the pin force at A. Assume W = 510 lb, a = 3.0 ft, b = 2.0 ft, r = 6 in. r W C Answer: A = i a B a A D lb b
A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50 kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 MPa
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
If the allowable bearing stress for the material under the supports at A and B is ob = 670 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. P a Answer: Pmax= i b lb
4) Determine the largest mass M of the rigid block which can be supported by the three rods if the allowable stress is 70 MPa for Copper and 140 MPa. for steel.. Copper A=900 L=160m E=120Gla (M) Steel A=12 L = 140mm E=2Gf Copper
The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, np = 0.4.