32. For the configuration shown in Fig. 2-22, calculate the weight of the piston if the gage pressure reading is 70 kPa. Ans. 61.6 kN Gage 1-m diameter Im Piston -Oil (sp gr = 0.86)

Q: ]means the repair work done to keep the system in good working condition.

A: It is required to fill the blank

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: 1 COP Nth False True

A: 1.COP=1/thermal efficiency False

Q: Car A is traveling at a constant speed VA = 120 km / h at a location where the speed limit is 100…

A:

Q: From the following identify  the false statement . In general safety precaution the machine should…

A: Precaution and safety

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: The moment arm is defined as a. the distance from the point of application of a force to a…

A: The moment arm is defined as

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: The gas turbine cycle consists of four thermodynamic processes as follows: 1-2: Work output from…

Q: If angular acceleration of pulley A is equal to 5 rad/s. The angular acceleration of C in rad/s is

A:

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 1 3. 9 TypehereIG 2.

A: Correct option: True.

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: Chip guard has to be installed between the point of operation and the operator, is a safety…

A:

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: Only one of the following is correct. Select the correct answer. Continuous process production has…

A: Given: Multiple choice question

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: This problem is based on Bratton cycle and can be solved as :

Q: The 10 kg wooden box A with a speed of 5 m/s as shown in Figure Q3 is 1 m from the stationary 10 kg…

A: Given data: ma=mb=m=10 kgua1=5 m/sub=0 m/sμk=0.6e=0.5 Need to determine the speed of box A just…

Q: If heat is added to a system and the temperature of a system increases, then the internal energy…

A: To find-: The heat is added to the system and the temperature of the system increases, then the…

Q: Which one of the below statements is mostly NOT correct about in creation of detailed design of…

A: The correct option is third. That is in selection of manufacturing process no. of components need to…

Q: 21:00 O O O 令. 63%i Details What is the value of the current 1? 5A 2A ЗА a. 12A O b. 10A Oc. 11A

A:

Q: *with heat Source energy balance

A: When constructing a heat exchanger, an energy balance calculation is frequently used to calculate…

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: The risk of damages in the life of a machine component can be eliminated by using individual…

A: This statement is (TRUE)

Q: ch of the following system sgive two examples of how mechanical engineer would be involved in the…

A: (a) Passenger automobile engine: Mechanical engineers have wide scope of expertise and the…

Q: PMM1 means, the machine does not follow the second law of thermodynamics Select one: True False

A: False

Q: From the following identify the false statement. O In electrical safety precaution, necessary steps…

A: From the above options ..

Q: 8 - A robot is used for loading and unloading of parts to automated flexible machines. Loading time…

A: Write the given data. tmachine=15 min        C1=30 TL/hour        C2=40 TL/hour Here, tmachine is…

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements

Q: The question is not answer fully. Please answer the second part of the question statement.

A:

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.

Q: UNITS: INCHES MATERIAL: ALUMINIUM -R.75 0.3 4.00 4.00 3.5 0.3 2.0 0.3 0.75 0.75 2.3

A:

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: Kinetic energy is the energy possessed by an object by virtue of its position Select one: True

A: Vector is a physical quantity that has magnitude and direction both. Scalar is a physical quantity…