30y Q-8:The velocity distribution v(y) in a wide channel is given by v(y) = 5.75 Vgy. S. log in which k y is the distance from the bottom and y, is the depth of flow, S, is the bed slope of the channel, k is the roughness height at the bed. Estimate the shear stress at 1 cm above the bottom of a channel on a slope of 0.5%. The depth of flow is 2.5 m and the characteristic roughness is 1 cm. If the critical shear stress required to move the bed material in the channel is 1 N/m2, find whether the channel is in stable condition. The viscosity of the water is 0.001 N/sm-2.

30y Q-8:The velocity distribution v(y) in a wide channel is given by v(y) = 5.75 Vgy. S. log in which k y is the distance from the bottom and y, is the depth of flow, S, is the bed slope of the channel, k is the roughness height at the bed. Estimate the shear stress at 1 cm above the bottom of a channel on a slope of 0.5%. The depth of flow is 2.5 m and the characteristic roughness is 1 cm. If the critical shear stress required to move the bed material in the channel is 1 N/m2, find whether the channel is in stable condition. The viscosity of the water is 0.001 N/sm-2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 11 A rectangular channel with width = 10 meters and depth = 3 meters has a flow slope of 0.001 and roughness n = 0.025. The flow rate is 80 m/s. Determine the shear stress on the channel in Pascals
The velocity of a trapezoidal canal with a bottom width of 1.4 m and side slopes of3H:2V is 1.2 m/s. Calculate the following if the flow depth is 2.18 m and the channelbed slope is 3.1 m per 3 kilometers.a. Flow rate, Qb. Roughness coefficient, nc. Shearing stress at the boundary of the canal, τ
Stress. Distribution in soil.
Consider a rectangular channel with an aspect ratio greater than 5 (width B and depth zo). The velocity distribution in the central plane of the channel is approximated as u = k1(z) 1/2. Here u is the streamwise velocity and is a function of the bed-normal direction z and k1 is a constant. Assuming the velocity distribution is similar across the width, calculate the average velocity for the cross-section, the energy and momentum coefficients.
A 120 cm diameter pipeline conveys oil (s=0.80) under a head of 150 m from the mainland to a nearby island, crossing a river (s=1.03) to a maximum depth of 6 m. If the pipe thickness is 8 mm, determine the stress in the pipewall in kPa. a.87,354.00 b.67,568.65 c.83,742,50 d.78,567.68
Question: In a free-floor flow environment, the base width in the trapezoidal cross-section given in the figure is B=5 m, Manning coefficient n=0.014, slope slope m=1.5, flow rate through the channel Q=40 m3/s flow of flow at h=yo =2 m uniform flow depth What should be the channel base slope lo for Calculate the type of current formed in the channel and the wall shear stress in case of uniform flow. 1 Yo =2 m m 5 т
Q3: A rough pipe has a diameter 80 mm. the velocity at a point 30 mm from the wall is 30% more than the velocity at a point 10 mm from the pipe wall. Determine (a) the average roughness height, (b) Darcy - Weisbach friction factor (f).
Water flows at flow rate Q In a rectangular canal. At height [m] 2 = h. And in width. b = 4 [m]. Manning's coefficient of roughness in the canal is. 0.015 = n Shear stress measured in channel tau = 9.81 In / m2). Next to the canal, a vertical partition was installed that divided the canal into two identical canals, the width of each canal being [m] 2 = 2/ b. A. Calculate the water level in each separate rectangular channel h h= ? b-4m B. The cross section changed to one connected rectangular channel as it was at the beginning when the water height is h = 2 [m] and width b = 4m. Add a step to the rectangular channel to create a control section (critical flow). Calculate the step height (delta (z) in the control section h=2m Az-!
Q.9 A plate of area 2m² on which fluid flow with 2y² Y velocity profile as "= 7 5'where y(m) is distance from plate, u(m/s) calculate shear stress (N/m²) at y = 0.4m from plate, when flow is laminar. Dynamic viscosity = 0.015 Pa-s
degree (a) = 14.01 gshsysujw thnx
4- A moderately curved channel with a slightly rounded non-cohesive bed material with a diameter of d50 = 25 mm carrying a discharge of 30 m³/s. The longitudinal slope of the channel is 0.001 and the side wall slopes are designed to be 60% of the angle of repose of the bed material Note: Use the Strikler's formula to calculate Manning's value. Use the Swammy and Mittal's formula to estimate the critical shear stress. Use the free board depth of 0.5m. a) Design the channel using the tractive force method for a Boly ratio of 20 b) Design the channel using the most efficient hydraulic section c) Discuss about the channel stability and erosion for both designs in parts a and b Strickler (Chow, 1959) proposed a correlation between the mean diameter of bed material, dso, and the Manning's coefficient as: n = 0.039d¹/6 Swamee and Mittal (1976) proposed an explicit equation to express the Sheild's curve defined as: 50 0.409d² 1/2 (1+0.177d² )¹/¹² T = 0.155+.
b) A pipe bend has a non-dimensional wall roughness value of e/D = 0.0002. The flow through this bend is highly turbulent. If the pipe bend has an equivalent length of Leq/D = 15, determine its resistance coefficient K.