300 mm 20mm 200 mm 90 mm 20 mmVv 20mm

Q: 1.Determine the maximum compressive stress acting on the cross section. 2.Determine the maximum…

A:

Q: Q.2) A state of stress is specified as shown in Figure (2), By using Mo determine the normal and…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(40+802)2+502R=78.1…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.5 in., d = 4.6…

A: Given- Mz= -4.35 kip-ft a=4.0 in b=5.5 in d=4.6 in t=0.33 in   It is asked to find 1. Maximum…

Q: Q4) ( ): A state of stress is specified as shown in Figure (4), By using Mohr's circle determine the…

A: .

Q: Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress…

A:

Q: normal stresses of 0 and 10 MPa (T)

A: Given:A rod element is oriented orthogonally to the horizontal and verticalσx=0 MPaσy=10 MPaτxy= 6…

Q: The rectangular plate is subjected to force P that causes elongation in the horizontal direction and…

A:

Q: ent about the z centroidal axis is M₂ = -4.05 kip-ft. um tension bending stress (a positive number)…

A:

Q: Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam…

A:

Q: Two rods, A and B, of equal free length are elastic. Both hang vertically 0.6m apart and support a…

A: Ad

Q: igure 2 depicts a structural frame with pin connection at A and D. Find the bending train energy in…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Q: Displacement components at a point in a solid u(x, y, t) = 2y²x + 2t v(x, y, t) = 8y³x³ + 5t? w(x,…

A:

Q: Q.6 A beam has solid circular cross-section having diameter d. If a section of the beam is subjected…

A:

Q: For the stressed elements allocated to you, find the values and sketch the orientations: a) Maximum…

A: Given data, Compressive stress along the y-axis, σy = -80 MPa Tensile stress along x-axis, σx= 40…

Q: The normal and shear stresses at a point in a structural subjected to a state of plane stress are…

A: To find principal stress and shear stress and their direction

Q: A cross section of a beam is shown. For any moment M, which surface of the cross section will have…

A:

Q: Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear…

A:

Q: A state of strains is defined by; €, = 250 x 106, €, = -350 x 106 and y»y = 400 x 10°. Analyze the…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Q: Problem#1 A cantilever beam along with its cross-section is shown in the figure below. 1) Determine…

A:

Q: The strain components &, &, and Yxy are given for a point in a body subjected to plane strain.…

A:

Q: the maximum tension bending stress (a positive number) in the beam. the maximum compression bending…

A: Given- moment about centroidal axis Mz= -3.65 kip-ft Co ordinates

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 4.7 in., d = 4.1…

A: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

Q: as shown in Figure (4), By using Mohr's circle determine the normal and shearing stresses and their…

A: Mohr's circle is a graphical representation of the equations for transformations of plane stresses.…

Q: 0=-80MPA o=20MPA 0=20MPA 0=-80MPA

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.