-30-35-40-45-20-25-10-1510-1-50010-1C3DA system identification experiment has been employed to the following systemK(+2₂)(+2₂)(s+p)(s+p₂)and the following Bode magnitude plot is obtained10⁰10⁰10¹a) Calculate the parameters of the transfer function, K, Z₁, Z2, P₁, P2b) Sketch the Bode phase plot of G(s). Label all slopes, frequencies, and phase angles on thedrawing. You are expected to use the logarithmic plot!10210¹c) Using the Bode plots, find/calculate the bandwidth, phase margin and gain margin.10²103

Given, a Bode magnitude plot of the system having transfer fucntion, ,we are required to:a) find the…

-30 -35 -40 -45 -20 -25 -10 -15 10-1 -5 0 9 0 6 10t " A system identification experiment has been employed to the following system K(+2₂)(*+*₂) (s+ P₂) (s + P₂) and the following Bode magnitude plot is obtained 10⁰ 10' 10¹ a) Calculate the parameters of the transfer function, K, Z₁, Z2, P1, P2 b) Sketch the Bode phase plot of G(s). Label all slopes, frequencies, and phase angles on the drawing. You are expected to use the logarithmic plot! 102 10² 10⁰ c) Using the Bode plots, find/calculate the bandwidth, phase margin and gain margin. 10

-30 -35 -40 -45 -20 -25 -10 -15 10-1 -5 0 9 0 6 10t " A system identification experiment has been employed to the following system K(+2₂)(+₂) (s+ P₂) (s + P₂) and the following Bode magnitude plot is obtained 10⁰ 10' 10¹ a) Calculate the parameters of the transfer function, K, Z₁, Z2, P1, P2 b) Sketch the Bode phase plot of G(s). Label all slopes, frequencies, and phase angles on the drawing. You are expected to use the logarithmic plot! 102 10² 10⁰ c) Using the Bode plots, find/calculate the bandwidth, phase margin and gain margin. 10

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Magnitude (dB) Phase (deg) 0 -5 -10 -15 -20 -25 -30 -35 -40 -15 -30 -45 -60 -75 -90 10 Bode Diagram Frequency (Hz) Assume an RC circuit filter has the bode plot shown above. 10* In units of dB, what is the magnitude of the transfer function at f = 900 Hz, |H(f = 900 Hz)|dB? |H(f = 900 Hz)|dB [dB] : _~15 rad B) In units of what is the approximate cut-off frequency, we, for the RC circuit? Do not leave sec' your answer in terms of . rad. We []:
Determine the transfer function that produced the following Bode plot. (Note: the values here were chosen so that this transfer function could be determined exactly): 120 Bode Diagram 100 80 60 40 20 45 -90 -135 -180 100 10 102 10 Frequency (radis) 10 (ge) pronbep (Bop) oe
12) In a series resonant RLC circuit, what is the impedance at resonant frequency? 12) A) Determined solely by de resistance B) The maximum impedance value C) Zero D) Infinity
15. ..) Given the following Bode plot, what transfer function for H(s) best defines this bode plot? 4018 30d8- 2008. 1000- -10 6 -2018. 14 a 10 d 100 40. (A +100) (+100) (A+109000) -20dB decade C₁ 100 (1 +100,000) 2 (2 +100) (A+1000) 1000 18,000 IF d. 00000 6. 40 (1 +1000) (A+100)ª(2+ 100,000)2 .-40dB de cade 100 (A+1000) (D+100) (A+ 100, 000) d i meg W
Start by finding the Thévenin equivalent circuit seen by the capacitance. Then, sketch the magnitude of the transfer function H(jw) = Vout/Vin. What is the value of the cutoff frequency?
Q3. For series RLC circuit, if the input is a voltage source and the output is the voltage across the resistor. 1. Find the transfer function If R=11 Q, C-10 mF and L-100 mH, answer the following questions: 2. Plot the magnitude Bode-plot 3. Find the gain in dB for o-50 and 1000 rad/s 5. If the input source is 5cos (500t+15), find the output voltage and show this case on the magnitude plot. 200
Quèstion 1 For the following RC circuit, R-100 ohm, C- 1pF 1. Derive the transfer function on your test paper. What is the transfer function? 2. If input is 20cos(200t-40) + 10cos(500ot+30), what is the output? 3. What is fu? Sketch the approximate straight line Bode magnitude and phase plot of the circuit on your test paper.
Represent (-99)10 in a) Sign Magnitude form and b) Sign 1’s Complement form. c) Sign 2’s Complement form.
A bode diagram of a second order system was measured and plotted as shown below. Use the graph to determine the transfer function of the system. Bode Diagram 20 -20 -40 -60 -45 -90 -135 -180 10° 10' Frequency (rad/sec) 102 10° Phase (deg) Magnitude (dB)
Using the Bode plot below of a system that has an initial gain Ki= 15, find the value of Kg needed to produce an 25% overshoot (*note* Ktotal = K * Kg). Bode Diagram 40 60 80 -100 -120 -140 -160 -180 45 -90 -135 -180 -225 -270 10 10 10 10 10 10 Frequency (rad/sec) Phase (deg) Magnitude (dB)
The magnitude and phase diagrams are provided for a passive filter. Input signal vin(t)=15 cos(20000t+100°) V is applied. What is the output voltage in V when t-1ms ? Series RLC H(s) -20 -30 -40 700 10 10 180 150 ... ... ... ... 100 ... 50 10 10 Frequency (rad'sec) Phase (deg) Mag (dB)
Plot the magnitude and phase plot for the following transfer function, use the templates from the class notes module so as to provide somewhat an accurate representation of the magnitude and phase plots. H (ju) 10 jw (0.01jw+1) (0.1jw+1)