3.6 k2 470 kn Bac-100 15 V 16 V

Q: Bet Bershat low -> 16 15() Ri 30 Rež

A:

Q: convert to Decimul (1oi2= %3D

A: Given binary number is 1011 . For converting binary (abcd)2 into decimal equivalent value…

Q: It's so hard to read, I need a handwrite version

A: We are not allowed to provide handwritten solutions. Hence, providing you typed solution shown…

Q: CALCULATE THE MISSING VALUES:

A: For circuit 1: U= I x R1   = 3mA x 600Ω   = 1.8 Volts

Q: (0) L, = ? 18 mH L 47 mH L5 22 mH LT 10 mH L4 30 mH ll ll ll

A: Simple problem on netwrok.

Q: 0.05x+0.10(150,000-x)=10,000 Solve

A: Given  An equation involving a single variable,we need to solve for X value. Please find the below…

Q: Base Current (Ib) of Tr1 Ib=___

A: Zener break down voltage VZ=5.6 V base current IB current gain hFE = 100 base to emitter voltage…

Q: Find the g parameters for the circuit in (Figure 1). Take R₁ = 2, R₂ = 15, R₂ = 80 N, R₁ = 152, and…

A:

Q: On part C, where did -0.7V come from? Part C is a whole different part than b, so I am confused how…

A: In general  we have to take  the base to emitter voltage of npn BJT as +0.7v where as for PNP BJT…

Q: Can you clarify how did u  get the answer? How to get 5.98x 10^-6 How it became 516.84 turns

A:

Q: Determine 13 in mA. Use the CVD model. VA = 6V R₁ = 3.4 kQ R₂ = 9kQ R3 = 0.26 kQ D₁ VA R₂ D2 R₁ R3

A: Given:a diode circuit,with we need to find:the value of I3 using CVD model.

Q: MPT occurs when Rth = 0 [Choose ] MPT occurs when Rth = RL [Choose ] MPT occurs when RL = 0 [Choose]…

A: For the given circuit the validity of the given statement needs to be identified.

Q: What is lami's theorem

A: Theorem The theorem is a statement that has been proved or can be proved. Lami's theorem is useful…

Q: The switch has been closed for a long time for t 0. 5Ω www i t=0 1.5 H m 10 22 9 A

A: At t<0 ,Switch is closed and 5 resistor is shorted. So, we can remove it.Since switch is…

Q: determine the fifth roots of -32 . Leave answers in polar form

A: Let x be the fifth root of -32 So    x = (-32)1÷5

Q: Determine the Fourier series representation for the signal x (t) shown in Fig. P. 4.2.9.

A:

Q: One of the simplest programming technologies is Cabling IC Fuse

A:

Q: Instructions: Solve the following. Show a complete solution. Box final answer. Fix the calculator to…

A: In this question,  Find the voltage Vo using the superposition theorem.  Here 3 independent energy…

Q: What does the Ampere-Meter labeled XMM1 show on its display? Note: R1=5kQ, R2=40k2, R3=10k2,…

A: Consider the given circuit,

Q: A LED which bright

A: Diode- When diode is forward biased it is short circuited in a circuit ideally. When diode is…

Q: 3b) Calculate 12 and 13 when /1 = 1 A.

A: The required current can be calculated by using mesh analysis. The mesh equation can be formed by…

Q: Determine current I, using mesh analysis j12n In jIon 80/90°V

A: According to the question we have to find the value of In.

Q: these errors occur from unknown sources O Arithmetic errors O Random errors O Systematic erorrs

A:

Q: Please answer in typing format

A:

Q: . Solve for Vc and Vâ 1.2 ka 10 uF 10 uF Vo B = 45 100 -9 V ww

A: We need to find current for given circuit

Q: QA The equation Fur Q'( NotQ) For FlipTis a) T+Q

A:

Q: 3V 나 Va 3k2 a) find Un

A: To find voltage VA

Q: If you havef=+10cm how can you design microscope? If you can`t why?

A: Microscopes used in older days used to have a single lens but the modern-day microscope used…

Q: Write an assembly code that will calculate the value of y in the following equation y = 2a + 3b-4c…

A: Aim:To write an assembly code that will calculate the value of y in the following equation y =…

Q: In a current measuring instrument, the element which converts low range instrument into high range…

A: We need tell about which winding will damage due to short circuit of potential transformer . We need…

Q: A LED which bright one color when forward and another color on reverse is called Dimensional LED O…

A: Answer:option-4  Multicolored LED.

Q: find d Req when Ri=10 2 R3 =lo. lo0 S2 Rea > R2

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.