3.39 The solid spindle AB has a diameter d. = 40 mm and is made of a steel with G = 77 GPa and 7a = 120 MPa. while sleeve CD is made of a brass with G (a) the largest torque T that can be applied at A if the given alloW- able stresses are not to be exceeded and if the angle of twist of sleeve CD is not to exceed 0.375°, (b) the corresponding angle through which end A rotates. 39 GPa and 7all 70 MPa. Determine C B 75 mm 200 mm = 6 mm 100 mm d. T A Fig. P3.39

3.39 The solid spindle AB has a diameter d. = 40 mm and is made of a steel with G = 77 GPa and 7a = 120 MPa. while sleeve CD is made of a brass with G (a) the largest torque T that can be applied at A if the given alloW- able stresses are not to be exceeded and if the angle of twist of sleeve CD is not to exceed 0.375°, (b) the corresponding angle through which end A rotates. 39 GPa and 7all 70 MPa. Determine C B 75 mm 200 mm = 6 mm 100 mm d. T A Fig. P3.39

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3.36 The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of aluminum (G = 27 GPa), deter- mine the angle of twist between (a) C and B, (b) D and B. 30 mm 30 mm 400 N- m GG 36 mm 900 N- m 36 mm 500 N. m B "0.6 m E. 0.5 m D m 0.5 Fig. P3.36
1. The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow = 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. B FAB 12 kip 8 in. FBD
Parvinbhai
Equal torques T = 5 kip · ft are applied to the two steel bars with the cross sections shown. (Note that the cross-sectional areas of the bars are equal.) The length of each bar is 8 ft. Calculate the maximum shear stress and angle of twist for each bar. Use G= 12 × 10° psi for steel. 5 in. 10 in. 2 in. 1.0 in. (a) (b) FIG. P3.52
8.8 (A/B). Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and CD is 500 mm long and has a hollow circular cross-section, the inside and outside diameters being, respectively, AB 25 mm and 60 mm, BC 25 mm and 70 mm, CD 40 mm and 70 mm. The modulus of rigidity of the material is 80 GN/m³ throughout. Calculate: (a) the maximum torque which can be applied if the maximum shear stress is not to exceed 75 MN/m²; (b) the maximum torque if the twist of D relative to A is not to exceed 2. [E.I.E.] [3.085 kNm, 3.25 kNm]
Answer by step of mechanical deformable bodies thank u..