3.39 The diagram shows a conical section fabricated from pure aluminum. It is of circular cross section having diameter D = ax2, where a = 0.5 m2. The small end is located at x₁ = 25 mm and the large end at x₂ = 125 mm. The end temperatures are T₁ = 600 K and T₂ = 400 K, while the lateral surface is well insulated. 4.x₂ (a) Derive an expression for the temperature distribution T(x) in symbolic form, assuming one-dimensional conditions. Sketch the temperature distribution. (b) Calculate the heat rate q.. 3.4 3.-

3.39 The diagram shows a conical section fabricated from pure aluminum. It is of circular cross section having diameter D = ax2, where a = 0.5 m2. The small end is located at x₁ = 25 mm and the large end at x₂ = 125 mm. The end temperatures are T₁ = 600 K and T₂ = 400 K, while the lateral surface is well insulated. 4.x₂ (a) Derive an expression for the temperature distribution T(x) in symbolic form, assuming one-dimensional conditions. Sketch the temperature distribution. (b) Calculate the heat rate q.. 3.4 3.-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the diagram below, metal 1 is made of gold and metal 2 is aluminum. Both bars have the same length and area of cross-section but their thermal conductivities are different. The temperature Th is maintained at a constant 88.0°C at the end A while the temperature T, at the end B is maintained at 19.0°C. A. T metal 1 metal 2 T (a) What is the temperature T; at the junction of the two bars? The thermal conductivity of gold is 318 J/(s · m · °C) and that for aluminum is 220 J/(s• m · °C). °C (b) If metals 1 and 2 are now interchanged, but the values of Th and T, are the same as in part (a), what will be the temperature of the junction? °C
A cable is made of two strands of different materials, A and B, and cross sections as follows: For material A: K=70,000 psi, n=0.5, A0=0.6 in2. For material B: K=25,000 psi, n=0.5, A0=0.3 in2 Calculate the maximum tensile force that this cable can withstand.
Question 9. The following non-homogeneous heat equation Ut = 3uxx +π-x models the distribution of heat in a metal rod. Solve the equation if the initial temperature u(x, 0) = x, and the the boundary conditions are: u(0, t) = u(π, t) = 0.
Figure Q4(a) shows the stress-strain curves of material A and material B. A circular rod of material A (diameter 3 cm, length 10 cm) is bonded to a circular rod of material B (diameter 4 cm, length 20 cm) as shown in Figure Q4(b). a) Based on the stress-strain curves shown determine the yield stress (σy) and the elastic modulus (E) of material A and material B.b) Assuming that the bond is rigid, determine the force P required to stretch the composite rod by 0.3 mm?c) Assuming a Poisson’s ratio value of 0.33, determine the change in diameter of the rod made from material B for the same P as determined in part (b).
i need the answer quickly
EXAMPLE 3.9 Finite-element²¹ analysis shows that a long structural component car- ries a uniform axial stress of 35 MPa (T) (Figure 3.29). A hole in the center needs to be drilled for passing cables through the structural component. The yield stress of the material is 200 MPa. If failure due to yielding is to be avoided, determine the maximum diameter of the hole that can be drilled using a factor of safety of 1.6. 10 mm H = 100 mm -d- Figure 3.29 Component geometry in Example 3.9.
materials resistance
2. One end of a 40 cm metal rod 2.0 cm2 in cross section is in a steam bath while the other end is embedded in ice. It is observed that 13.3 grams of ice melted in 15 minutes from the heat conducted by the rod. What is the thermal conductivity of the rod.
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi, 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L1=30 in., L2=48 a = %3D in., a=32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1)
i need the answer quickly
please help me with this
Kindly show a step-by-step solution. Thank you A 6m rod with a 4mm gap between one of its ends and the surface of the wall next to it is secured solidly between two walls at 25°C. Calculate the highest temperature that the rod can withstand in degrees celsius while taking into account the maximum limiting stress of 67 MPa, where a = 19.5 m/mC°, and E = 130 GPa.