3.34 Mathematically determine the reaction forces at A and B for the truss shown in Fig. 3-44. Ans. A, 10 kips, A, 13.3 kips, B,-0, B, 13.3 kips - -8 ft- -7 ft- 6 ft 10 kips T 4 A sadl goeU 3 Fig. 3-44 od gra B 8E-E ad geU ACC

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out -  (f) Length of Curve (h)…

Q: How can I find GH, EG and FH

A:

Q: Quiz #1 Problem 1: Prove the following relationship. Gs Y. (1+ Mc) Y =- 1+e

A:

Q: complete the following set of profile level notes and show the customary arithmetic check.

A: Height of instrument method:HI=Elv+BMElvi+1=HIi-FS or ISExampleHI at BM-a:HI=234.51+1.24=235.75Elv…

Q: Only Draw profile with appropriate scale

A: To draw the profile to the given levelling

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: usescale (1/1) draw the front Section view in mides pan and the side Sectional Vien middles pan for…

A: Front Sectional View: The front sectional view is the view of the object done by taking a section…

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: R10 30 50 O. 15 R30

A:

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: Draw the influence lines for the vertical and horizontal reactions, Ax and Ay, at support A and the…

A: Question consist of truss supported at hinge support at A and G . Length of members are given in the…

Q: 205, 406 ton=722 %3D How are Yoll tonne - 72 %31

A: Give that, Tonne is metric measure  1 TON  = 0.90718 tonne   TON is American unit

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: 1. Ah = [ Select ] 2. Av [ Select ] 3. MA = [ Select ] %3D 4. C, = [Select ] 5. Dy = [ [ Select ] 50…

A:

Q: Q4: Convert the following into required: 1- An area 4.2 cm on amap with scale 1/5000 > Don , Olk,…

A:

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: how is A1 solved

A: Answer Area A1 is solved using  scientific calculator. Use 'X' in place of 'A1' in Scientific…

Q: Explnation of EPDM.

A: The ethylene propylene diene monomer is abbreviated as EPDM.

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Convert 0.0351 to engineering notation. O a) 35.1 × 103 O b) 3.51 × 10–2 )c) 3.51 x 10² O d) 35.1 ×…

A: Solution:- We have to convert the given number into the engineering notation, The given number is…

Q: express each measurement in inches.41⁄2 feet

A: GIVEN :- Measurement = 412 feet To Determine :- Convert the given measurement into inches.

Q: Y

A:

Q: In the figure below, find the SAB 0 ,CAB OCF %D

A: Given data E=200000MPa P=36kN

Q: 3. £ 65 s² + 25 + 3 s² + 25

A:

Q: The block of mass m1 = m0 is attached to a spring of elastic constant k = (m0g)/H and natural length…

A:

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Q: Define Torsion,

A: Torsion: The twisting of a material by the loading of external forces i.e couple which produces…

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.