3.106 Copper is an excellent electrical conductor widely un in making electric circuits. In producing a printed circ board for the electronics industry, a layer of copper laminated on a plastic board. A circuit pattern is th printed on the board using a chemically resistant pc mer. The board is then exposed to a chemical bath t reacts with the exposed copper, leaving the desired c per circuit, which has been protected by the overlay polymer. Finally, a solvent removes the polymer. One action used to remove the exposed copper from the cuit board is Cu(s) + Cu(NH),Cl2(aq) + 4 NH3(aq) - 2 Cu(NH3)CH A plant needs to produce 5000 circuit boards, each w a surface area measuring 2.0 in. x 3.0 in. The boards covered with a 0.65-mm layer of copper. In subsequ processing. 85% of the copper is removed. Copper he density of 8.96 g/cm'.Calculate the masses of Cu(NE Cl2 and NH3 needed to produce the circuit boards. suming that the reaction used gives a 97% yield.

3.106 Copper is an excellent electrical conductor widely un in making electric circuits. In producing a printed circ board for the electronics industry, a layer of copper laminated on a plastic board. A circuit pattern is th printed on the board using a chemically resistant pc mer. The board is then exposed to a chemical bath t reacts with the exposed copper, leaving the desired c per circuit, which has been protected by the overlay polymer. Finally, a solvent removes the polymer. One action used to remove the exposed copper from the cuit board is Cu(s) + Cu(NH),Cl2(aq) + 4 NH3(aq) - 2 Cu(NH3)CH A plant needs to produce 5000 circuit boards, each w a surface area measuring 2.0 in. x 3.0 in. The boards covered with a 0.65-mm layer of copper. In subsequ processing. 85% of the copper is removed. Copper he density of 8.96 g/cm'.Calculate the masses of Cu(NE Cl2 and NH3 needed to produce the circuit boards. suming that the reaction used gives a 97% yield.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

(d) Calculate the electrical conductivity of a 6.0 mm diameter cylindrical silicon specimen of 60 mm long in which a current of 0.5 A passes in an axial direction. A voltage of 12.5 V is measured across two probes that are separated by 40 mm. i. Compute the electrical conductivity of the specimen. C12334 ii. Compute the resistance over the entire 60 mm of the specimen using the data in (1).
No need to solve anything under the calculations. I've provided it so that the, Explanation question could be answered.
Balance the following reaction. The charge on Cu in CuS is 2+. You may add additional phases but not components to achieve this. Show your working out. CuS(s) + HNO3(aq) --> CuSO4(s) + NO(g)
us_engine.html?ClassID=1563099459# nt Orie.. A manufacturer wants to generate chromium plate, but had only potassium dichromate as a reagent to start with. An acidic solution of potassium dichromate can be reduced to chromium(III), which can be further reduced for plating according to the reactions below. Cr203- + 14H*+ 6e¯ → t. 2Cr3+ + 7H2O Cr3+ + 3e Cr How many electrons are transferred to produce ONE chromium atom during the combined processes? [?]e /Cr atom Number of Electrons Enter
What is special about the following terms: (i) Kraft Temperature (ii) Sorption
In a converter, 9.33 kg of SO3 is fed and allowed to come into contact with a certain amount of 91.34% H2SO4 to produce 4.71% oleum. How much oleum was produced in kg? Use the following molecular weights: 80 kg/kmol SO3, 98 kg/kmol H2SO4.
A coil with 193 turns has a magnetic flux of 37.3 nT-m² through each turn when the current is 1.90 mA. (a) What is the inductance of the coil? What are the (b) inductance and (c) flux through each turn when the current is increased to 3.53 mA? (d) What is the maximum emf & across the coil when the current through it is given by i = (2.72 mA)cos(wt), where w = 205 rad/s? (a) Number 3.788894737 Units mH (b) Number 3.788894737 Units mH (c) Number i 6.929947369 Units nWb (d) Number i 2.112687705 Units V
OUTM FINAL EXAMINATION UTM OUTM UTM 60TM PIRAL TM OUTM PIRAL OUTM OUTM "Tos UTM Figure 5 a) Figure 5 showed applications of alloys as roofing materials (Figure 5a) and automotive body parts (Figure 5b). Suggest non-ferrous alloys that could satisfy each application. Justify your selection with the inclusion of comparison for mechanical strength requirements between both applications.
Q3: A silicon is doped with 1017 boron atoms/cm-3. What is the electron concentration (n) at 300 k?. What is the resistivity? H, = 250- n = 1.5 x 101°cm-3 -2 and V.S (Ans. 2.25 x 10 cm-3,0.250.cm).
Please answer 1 a, b, and c.
Significance of your results: Titanium is also commonly anodized, but does not need to be dyed to achieve colored surface layers. Instead, the color comes from thin-film refraction within the oxide layer - the color is characteristic of the thickness of the oxide layer. Ti²+ (aq) + 2e-Ti (s) E° = -1.60 V TiO₂ (s) + 4 H+ (aq) + 4 e-Ti (s) + H₂0 (1) E° = -1.076 V a. What is the half-reaction at the anode for the anodization of titanium? b. Under standard conditions, what is the smallest potential you would need to provide in order to anodize titanium?
Question 3 To Vacuum Pump Substrate Deposition of thin film Vaporized material Vaporized material Target material Evaporator Heater Target material Substrate Magnet To Vacuum Pump Electron beam Electron gun (a) Identify the two Physical Vapor Deposition Techniques in relation to the figure. (b) Why is a vacuum pump needed to achieve the deposition of the thin film?