3.1 A 1-km-long, 10-Mbps CSMA/CD LAN (not 802.3) has a propagation speed of 200 m/isec. Repeaters are not allowed in this system Data frames are 256 bits long, including 32 bits of header, checksum, and other overhead. The first bit slot after a successful transmission is reserved for the receiver to capture the channel in order to send a 32-bit acknowledgement frame. What is the effective data rate, excluding overhead, assuming that there are no collisions?

3.1 A 1-km-long, 10-Mbps CSMA/CD LAN (not 802.3) has a propagation speed of 200 m/isec. Repeaters are not allowed in this system Data frames are 256 bits long, including 32 bits of header, checksum, and other overhead. The first bit slot after a successful transmission is reserved for the receiver to capture the channel in order to send a 32-bit acknowledgement frame. What is the effective data rate, excluding overhead, assuming that there are no collisions?

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Similar questions

A 1-km-long, 10-Mbps CSMA/CD LAN (i.e., Classic Ethernet)has a propagation speed of 200 m/μsec (i.e., how fast the radio signal moves on the link). Thereare no repeaters in this system. Data frames are 512 bits long, including 480 bits of payload (i.e.,effective data) and 32 bits of overhead (e.g., header, checksum, and other overhead fields). Everydata frame should be confirmed by a 64-bit ACK frame. We assume the sender needs to use onecontention slot to seize the channel before transmitting the data frame, and the receiver needsto use one contention slot to seize the channel before transmitting the ACK frame. Answer thefollowing questions: a. What is the minimum length of a contention slot in μsec? b. What is the effective data rate for the sender to send one data frame? Assume that there areno collisions. Show the calculation c. What would be the impact on the total delay and the effective data rate if we used a longerdata payload size in the data frame? Given one application…
Assume that the propagation speed in a coaxial cable is 2 ∙108 m/s a. Packets are transmitted using the ABP (alternate bit protocol) over a full-duplex 5-km coaxial cable with a 5 Mbps transmission rate. The packets and ACKs are 1500 bits long. The transmitter and receiver use a CRC chip and their processing time is negligible. How many packets are transmitted every second when there is no transmission error? b. Five transmission lines identical to the one discussed in a) are connected in series. A buffer is used at each connection between the links to store packets as required. How many packets will go through the five lines every second when there are no transmission errors? Now assume that a packet or its acknowledgement is corrupted on any given link with probability p. What is the new packet transmission rate through the five links? Comment. Assume the processing delays and queuing delays for both ends are negligible.
Suppose that we are sending a 30 Mb MP3 file from a source host to a destination host. All links in the path between source and destination have a transmission rate of 10 Mbps. Assume that the propagation speed is 2 × 108 meters/sec, and the distance between source and destination is 10,000 km. 1. Now suppose there is only one link between source and destination, and there are 10 FDM channels in the link. The MP3 file is sent over one of the channels. What is the end-to-end delay?
The following frame should be transmitted over a given network (the frame is shown in hexadecimal): 7E DB DD 7E C0 7D DB DC FF C0. a) If the SLIP framing protocol is used; what are the bytes that are sent on the wire (after framing)? Show your work
q11- This question involves estimation of error handling overhead for a communication link which has a BER of 10−2 Forward error correct (FEC) Frame: Total 1144 bits 1024 bit of data 120 FEC bits Error Detection + automatic repeat request (ED + ARQ) Frame: Total 1074 bits 1024 bit of data 50 CRC bits a) Our task is to find the approximate frame error rate (FER) for FEC in percentage Answer: Answer b) Estimate the approximate overhead for ED + ARQ in percentage Answer: Answer
O Differentiate between error detection and error correction. A bit string needs to be 0110111111100111110111111111100000 transmitted at the data link layer, what is string actually transmitted after bit stuffing, if flag patterns is 01111110?
IV Figure below shows a multiplexer in a synchronous TDM system. Each output slot is only 10 bits long. (3 bits taken from each output plus 1 framing bit . Assume that the framing bits consist of 1 bit per frame and the bits are alternating between 1 and 0.) What is the output stream? The bits arrive at the Multiplexer as shown by the arrows: 101110111101 Frame of 10 bits 11111110000- TDM 1010000001111-
My id last two digit =32 so x1x2=32 Subject:Datacommunication