3. Two electric motors are being considered to power an industrial hoist. Each is capable ofproviding 100 hp. Pertinent data each motor are as follows:Motor AMotor BInvestmentP 25,00084%P32,00088%Electrical EfficiencyAnnual Maintenance400600Life, years1010Money is worth 20%, If the expected usage of the hoist is 700 hours per year, what would the costof electrical power have to be before Motor A is favored over Motor B?

Electrical power means the current flow in electric charge and the voltage potential of charge…

3. Two electric motors are being considered to power an industrial hoist. Each is capable of providing 100 hp. Pertinent data each motor are as follows: Motor A Motor B P32,000 Investment P 25,000 Electrical Efficiency 84% 88% Annual Maintenance 400 600 Life, years 10 10 Money is worth 20%, If the expected usage of the hoist is 700 hours per year, what would the cost of electrical power have to be before Motor A is favored over Motor B?

3. Two electric motors are being considered to power an industrial hoist. Each is capable of providing 100 hp. Pertinent data each motor are as follows: Motor A Motor B P32,000 Investment P 25,000 Electrical Efficiency 84% 88% Annual Maintenance 400 600 Life, years 10 10 Money is worth 20%, If the expected usage of the hoist is 700 hours per year, what would the cost of electrical power have to be before Motor A is favored over Motor B?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A DC motor is fed with the armature voltage 430 V. At the current load, the speed is 180 rpm and the armature current is 29 A. The armature resistance of the motor is 0.9 Ω and the brush voltage drop is a total of 2.5 V. The shaft torque is 72 Nm and the magnetizing current is 0.87 A at the magnetizing voltage 494.5 V. a) What electrical power does the motor receive? b) what is the mechanical effect that the engine develops? c)determine the efficiency of the motor at this load d) how big will the speed be at half the load torque? (Armature voltage and magnetizing current are unchanged.) Tip: First calculate the motor's k2Fi value - half Half the torque gives half the armature current. e) The speed at idle is approximately (whole number with two decimal places)
A linear machine has the following parameters: The battery voltage, V = 120 V, The internal resistance of the battery R = 0.4 02, The length of the bar is1 meter, and the magnetic flux density B = 0.5 T (out of the page). What is the no load steady-state speed of the bar at starting? 1=0 R www O a. Speed VSS = 240 m/s to the right O b. Speed Vs = 240 m/s to the left O c. Speed Vss = 48 m/s to the right O d. None e. Speed Vss = 48 m/s to the left B 1
UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES.
2. Explain which of the following instructions are invalid? State the invalidation reason and give the correct form for invalid instructions: a. MOV DL,AX b. MOV ES,CX c. MOV [BX],[2000] d. MOV BX,[AX] e. MOV CL,[BL+200] f. MOV 1234,DX g. MOV CH,[BX+SI+300] h. MOV DS,[SI+DI-5] i. MOV [4500],1234 j. MOV 200,[300]
ENGINEERING UTILITIES (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. BOX THE FINAL ANSWER.)
None
A Van-de-Graaf generator produces 1000 N force on its belt. A variable speed motor drive is driving the generator directly. The diameter of the pulley on the motor side of the generator is 20 cm. If the input power of the motor is 1.5 kW and its efficiency is 96%, what must be its speed in revs/min?
Q17 Draw The magnetization curve of a de machine
The rated load of a 300 V shunt generator is utilized. If the driving engine generates 55 horsepower and the armature resistance is 0.05 ohms and the shunt field resistance is 50 ohms, SPL is equal to 400W. then calculate the mechanical, electrical, and overall efficiency of the generator.