3.- Three rods with lengths L1=1.5m, L2=1.2m and L3=1m are welded at center C. One applies three forces with magnitudes F=12N, F;=35N; F;=40N along directions shown in figure. Find: a) The direction and the magnitude of each torque versus C-point. b) The direction and the magnitude of net torque versus C-point.

3.- Three rods with lengths L1=1.5m, L2=1.2m and L3=1m are welded at center C. One applies three forces with magnitudes F=12N, F;=35N; F;=40N along directions shown in figure. Find: a) The direction and the magnitude of each torque versus C-point. b) The direction and the magnitude of net torque versus C-point.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question #2: The 1.0-in-diameter solid steel shaft shown in figure is simply supported at the ends. Two pulleys are keyed to the shaft where pulley A is of diameter 8.0 in and pulley B is of diameter 5.0 in. (1) Determine the reaction forces (2) Draw the shear force and bending moment diagrams (3) Draw the torsion diagrams 300 lbf 1 dia. 5 dia. 50 lbf 8 dia. 470 lbf 6 00 70 lbf
The frame shown in Figure below consists of two members (BC and ABD) and it is subjected by the given point loads. Find all pin forces that act on this frame. 100 N 120 N -300 mm 500 mm 300 mm B D 300 mm A 100 mm 600 mm
The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm
Question 4 fixed. The shear modulus G and the polar moment of inertia I, of the bar's cross-section are constant along the bar's axis. From the fixed left end (x = 0) of the bar to the middle (x = L/2) of the bar, a lincarly varying distributed torque t, = kr, 0 < x < L/2 is applied (the unit of t, is N-m/m). At the free end (r = L) of the bar, a concentrated torque T is applied (the unit of T is N-m). According to the right-hand rule, the linearly varying distributed torque t, and the concentrated torque T both point to the r-positive direction. Find the angle of twist at the free end (x = L) (Expressing the result with G, Ip, L, T, and k). (Hint: It is easier to find the angle of twist using & = f Figure 1 shows a bar under torsion. The left end of the bar is E.) t, = kx L/2 L/2 Fig. 1. The left end (r = 0) of the bar is fixed, and the right end (r = L) of the bar is applied with a concentrated torque T. A linearly varying distributed torque t, is applied from the left end (z = 0) of…
The wooden frame is constructed from wooden 2” X 4” Lumber (Nominal size; Actual size: 1 ½” X 3 ½”) and bears a uniform distributed load. All connections are pin connected. If wo = 100 lb/ft, and L = 9 ft. Note that the distributed load is the force per unit length in the horizontal direction. A) Find the vertical reaction force at A. 747 450 248 900 563 B) Find the normal stress perpendicular to the grain at point D. -26.4 -33.9 -85.7 -21.4 -66.9 C) Find the shear force, V, on the cross-section at E. 106 900 159 150 35
2: The forces acting on gear-shaft-bearing system are shown in the figure given below. a) Calculate the force Fg b) Find the support reactions at 0 and C c) Obtain the bending moment diagrams (M, and My) d) Obtain the torque diagram (Mx) e) Calculate o (bending stress) and t (torsional shear stress) at a point where the maximum bending moment is observed f) For this point, compute the principal and maximum shear stresses 400 mm 350 mm 25° 300 mm FA= 11 kN olo 20° 50-mm dia. A Gear A, 600-mm dia. /C B Gear B, 300-mm dia.
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
Find all the non-zero components of internal reaction forces in section a-a. If you select wrong answers, you will have negative score in this question. 200 mm 200mm D 400 N 800 N
2 B 2