3. The truss in Figure is pinned to the wall at point F, and supported by a roller at point C. Calculate the force (tension or compression) in members BC, BE, and DE. (Method of Sections-25 points) 4 m 5 m 4 m B. 4 m 80 kN 60 kN

3. The truss in Figure is pinned to the wall at point F, and supported by a roller at point C. Calculate the force (tension or compression) in members BC, BE, and DE. (Method of Sections-25 points) 4 m 5 m 4 m B. 4 m 80 kN 60 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Refer to the truss shown a. Determine the maximum positive ordinate for member DC. b. Determine…

A: First we will draw the Influence lines for member AB and DC

Q: Problem 5: Method of Sections Inputs: ● ● ● B H I a d = 4 m a = 3 m (all horizontal members are this…

A: Given data in question Load 45 kN Span 3 m each and 4m To find out Force in member CJ

Q: Determine the reactions and the force in each member of the trusses shown using methods of…

Q: Use method of the section to calculate the bar forces for the truss given below: V 24 3

A: Consider the free body diagram of the given truss as shown below.

Q: For the truss and loading shown; a.) determine the force in all the truss members. 3 kN b.)mention…

A: Finding out forces in member.

Q: Find the force in each member of the truss shown. Indicate whether it is in tension (+) or…

Q: -1.5 m- 6 kN 2 m 10 kN- C 2 m A B

Q: F E L/3 D В A P L/3 L/3 L/3

Q: 5. M 5 m 7 m 5 m 7 m

Q: UPVOTE

A: As there are two different questions posted, according to the guidelines, only the first is being…

Q: Draw the Free Body Diagram Solve step by step Always used 3 decimal places

A: Given figure shows the parker truss. It is required to find the forces in members BD, BE, CE and DE…

Q: 1 kN 2 kN 2 kN 2 kN J 1 kN H 0.46 m F D 2.62 m В I A C G 2.4 m 2.4 m 2.4 m 2.4 m

Q: 3. Use the method of sections to determine the internal forces in members FE, BE, and BC. The…

Q: The electric power transmission tower supports two wires that apply 18 kN vertical forces, and the…

A: Determine the force in members IF, IM and BD.

Q: SOLVE FOR THE FORCE IN ALL MEMBERS OF THE TRUSS. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND…

Q: Show complete solution. Draw the following structures then classify whether Statically Determinate,…

A: Static indeterminacy is a conjecture that shows the difference between the total number of unknowns…

Q: Problem 1: A roof truss is made with an angle bar 50mmx25mmx6.35mm connected as shown. The material…

Q: 11. Determine the force in each member of the truss shown using method of joints.

A: Objective: To determine the force in each member of the given truss using the method of joints.…

Q: The space inverted pyramidal truss with rectangle base is modified. The support at D is changed as…

A: Given diagram:-

Q: Solve using the method of sections. Determine the force in members BC, CH, and GH of the 3 m truss…

Q: Determine the force in member BE of the loaded truss. Th 20 46 13 Answer: BE = B 15- E 21 11 -13- 20…

Q: a) 8 kips. 16²7 36 kips 16' E B 24 kips 12 12² ↓

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: Determine the force in member GF (in kN, round-off to 2 decimal places, include "_" if in…

Q: B ба E M 7a D L

Q: | 48 kN -4 m-4 m C 4.5 m E Compute the force on EACH member of the truss. Classify each forces…

Q: A rigid bar AB' and "CD as shown are supported by pins at "A" & "C" and two ross. Determine the…

Q: Consider the 21- member truss shown; determine the zero-force members and force in each member then…

Q: F G H 3 m A E B 40 kN 40 kN -4 at 3 m = 12 m-

Q: The Warren truss loaded as shown is supported by a roller at c and a hinge at G. By the method of…

Q: H.W. Determine the horizontal and vertical comporents of force at pins A and D. 03n 12 KN

A: To find reactions at A and D

Q: The space inverted pyramidal truss with rectangle base is modified. The support at D is changed as…

A: Given data:- AM¯=9a

Q: Cldan writing and hand written please

A: Determine the force in each members of the truss. Let's solve using method of joint.

Q: Determine the approximately the force in each member of truss. Assume the diagonals cannot support a…

Q: For the truss shown below, P = 9.1 kips, a = 7 ft, and b = 6 ft. Determine the force in member 3…

A: It can be solved by two method 1 - by method of joint,

Q: Problem. Find the reactions and the stresses in all the members of the truss as shown in the figure.…

A: From the given question it is required to calculate reactions and forces in all the members of the…

Q: DIRECTION: Solve and Analyze the following problems in neat and orderly manner. Use your indicated…

Q: Determine (approximately) of the force AE, AB and EF of the truss. Assume the diagonals can support…

A: The method of sections is a process used to solve for the unknown forces acting on members of a…

Q: A 3 m D B 3 m 35 KN F E C 10 KN 4 m . 10 KN 4 m

Question

3. The truss in Figure is pinned to the wall at point F, and supported by a roller at point C.
Calculate the force (tension or compression) in members BC, BE, and DE. (Method of
Sections-25 points)
4 m
5 m
4 m
B
4 m
80 kN
60 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the truss shown: (a) Identify all zero force members (b) Determine the force in members AE and CB and indicate whether the members are in tension or compression. Note that both supports A and B are pins. MUST DRAW A FREE-BODY DIAGRAM. 2 kN- 15 m 4 kN- 1.5 m E с 4m YOB
Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform 1 rectangular cross section of x 1 in. Determine the largest load which can be suspended from 4 point E if the deflection of E is not to exceed 0.02 in. 8 in. A 8 in. B O A 10 in. D 17 in. E
Specifying tension or compression: determine Forces in the members AB, and AK by the method of nodes;
For the truss shown below, P = 9.8 kips, a = 9 ft, and b = 6 ft. Determine the force in member 1 (tension is positive). Give the answer to one decimal place.
For the truss shown below, P = 9.5 kips, a = 8 ft, and b = 7 ft. Determine the force in member 2 (tension is positive). Give the answer to one decimal place.
Determine the forces in all bars of the truss. Indicate tension/compression. Any methods will do
Using the method of sections, determine the force in members BD, DE and DF. D 1 m F 20 kN В 1 m A C G H E 1.5 m 1.5 m 1.5 m 1.5 m 40 kN 40 kN
???????: ?????????? ?????? ?? ?????? ?? ??????????
The truss shown is designed to support a staircase. For all questions, indicate whether the members are in tension or compression. Assume that all joints are pinned. Use the method of sections for each part. a. Determine the force in members EG, FG, and HF FEG=3,96 kN (C) Ft 1.70 KN (T) Fee- 400N (T) b. Determine the force in members EF and DF Far= 400N (C) For =1.26 kN (T) 400 N 800 N 2 m 800 N 2 m E 2m F 800 N 2 m 2 m D. 2 m 400 N 45 2 m B.
For the truss shown below, P = 9.1 kips, a = 9 ft, and b = 7 ft. Determine the force in member 1 (tension is positive). Give the answer to one decimal place. Type your answer..
Solve the frame USING: Portal Method