3. The slotted arm OA forces the small pin to move in the fixed spiral guide defined by r = K0. Arm OA starts from rest at 0 = π/4 and has a constant counterclockwise angular acceleration Ö = a. Determine the magnitude of the acceleration of the pin P when 0 = 3π/4. A -P

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: Calculate the time to complete one circular motion. How to double the time?

A: Given data:Helicopter mass = 400 kgcircular motion radius, r = 20 mRotor blade resonant frequency =…

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: lease write a precise overview/description of the precision tweezer below specifically for each…

A: Given Data : Precision tweezer

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: Files are used for removing large of amount of materials. Select one: True False

A:

Q: Please send Complete answer for getting upvote  Detailed answer  what is Flyweight Design Pattern…

A: given; what is Flyweight Design Pattern Application  Real world example

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: Explain the diagrame! C. Ca

A: Solution:   In the diagram, Cm is the Moment Coefficient. CL is the Lift Coefficient.

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Calculate the time to complete one circular motion.

A:

Q: A solid cylinder is rolling down a ramp that is rough enough to cause the cylinder to roll without…

A: This question is solved with the help of the law of conservation of energy. Under pure rolling,  The…

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: What is its minimum width if it produces 1000 minima?

A: The expression for the dept of the slits is given by the expression, Dsinθ=mλ For the minimum width…

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: Force 20 N on object does not displace the object. What is work done value

A: To Find :  the work done . Given :  The Force is F=20 N. The displacement is d=0. Formula used: The…

Q: Required information Sally is making a sine bar, which is used to machine angles on parts (see the…

A: Given data: Thickness (t)=1.25 inGroove angle=90°Cylinders diameter d=1 inD=5.6 inθ=22.5° Need to…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The spool shown in the figure has a weight of WAB and its center of gravity is located at its center…

A:

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: can this be done using simpsons rule?

A: As already calculated using the relation    for the volume ranging from to  in steps of , the…

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.