3. The figure shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 700 mm² for AB and 450 mm² for AC. Determinethe maximum safe value of W if the working stresses are 110 MPa for AB and 120 MPafor AC.B31245W

3. The figure shows a two-member truss supporting a block of weight W. The cross- sectional areas of the members are 700 mm2 for AB and 450 mm2 for AC. Determine the maximum safe value of W if the working stresses are 110 MPa for AB and 120 MPa for AC. 3 12 W

3. The figure shows a two-member truss supporting a block of weight W. The cross- sectional areas of the members are 700 mm2 for AB and 450 mm2 for AC. Determine the maximum safe value of W if the working stresses are 110 MPa for AB and 120 MPa for AC. 3 12 W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the Mohr's circle of stresses that describe each of the following states of stresses. 700 kPa 4 MPa 40 MPa 600 kPa (a) (b)
Determine the gross area of steel needed to design the bar force members at BC, BE, and AE. Stress in steel is A36 = 36 ksi 400 Ib 300 lb 15 ft 25 ft 15 ft 50 Ib E 30 ft A
Consider the truss shown in (Figure 1). Suppose that F = 30 kN Figure A 3m 3m < 1 of 1 ▼ Determine the force in the member CD of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case tension. FCD- Value Submit Part B HA Part C Request Answer Determine the force in the member CB of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCB- Value Submit Request Answer HÀ Submit Part D FDA- Value HA Determine the force in the member DA of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive…
1. See figure below and solve for the maximum value of torque the composite shaft can accommodate given a maximum shear stress of 8ksi in bronze and 12 ksi for the steel. Assume bronze has G = 6 x 10° ksi, and for steel, G = 12 × 10º ksi. 2" Steel Core D = 2 in Hollow Bronze D = 3 in, d = 2 in
If the steel has a stress of A100 = 100 ksi, what is the gross area of the steel required to design the bar force members AE, BE, and BC?
A small aluminum alloy [E = 74 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 130 mm. The cross- sectional dimensions of the tee shape are b = 25 mm, d = 38 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage- d В D E 2 H Answer: P= i N
Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2
A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 220 mm. The cross-sectional dimensions of the tee shape are b = 18 mm, d = 27 mm, and t = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 με is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P
Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter rivets placed in a zig-zag pattern. The pitch of the rivets is 75 mm and gauge is 60mm. If the allowable tensile stress is 150 MPa, the maximum tensile force that the joint can withstand is
For the truss shown, Fi=240KN and F2=720KN. Determine the forces in the rod BD and the rod BE (unit of length is m). Figure Q3 Need detailed and step by step answer don't copy from chegg or internet i match ur answer
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P |1 Strain gage- d D E 2 H b Answer: P= i N
A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b %3D = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a %3D compressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P В D E Strain gage- d H b Answer: P = i N