3. The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to rivets. How many 19mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? -14-mm-thick gusset plate 6m -13-mm-thick angle G. 4 m 4 m 4 m 4 m 96 kN 200 kN 96 kN PRE 6-mm-thick angle Pac

3. The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to rivets. How many 19mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? -14-mm-thick gusset plate 6m -13-mm-thick angle G. 4 m 4 m 4 m 4 m 96 kN 200 kN 96 kN PRE 6-mm-thick angle Pac

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thicknesses shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 20-mm-diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE?
1.45 A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections with the thicknesses shown in the figure are members BC and BE. Shear in the rivets has a working stress of 70 MPa, while bearing stress due to the rivets has a working stress of 140 MPa. To fasten the following members to the gusset plate, how many 19-mm-diameter rivets are required: (a) BC; and (b) BE? 14mm-thick gusset plate 13mm-thick angle bar 6m 6mm-thick BE angle bar C. 3m 3m 3m 3m Рвс 100KN 200kN 100KN
ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to fasten the said members to the gusset plate? K.R.R.P. wwwwwwww 00 400 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B 75X75X6 mm ------------- · ET---- I 14 mm thick GUSSET PLATE P BC 75X75X13 mm P BE
Complete solution with free body diagram
I need the answer as soon as possible
A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thicknesses shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 19-mm-diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE?
1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle section with the thickness shown in the figure. The working stresses are 155 MPa for tensile member and 145 MPa for compressive member, 50 MPa for shear in the rivets and 130 MPa for bearing stress due to the rivets. How many 20 mm diameter rivets are required to fasten member DE to the gusset plate? 12 kips 8ft 12 kips 10 kips 8ft 10 kips 6ft B 4ft E F 4 ft 4 ft 22 ft 8 ft
Trusses 1. Find the stresses of FAB. FAC., FBC & FBD- 20 k 15 k D 60° 60 60° 5' 10 10 Ra Rb
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. Please show your complete handwritten solution. Thank you
Q2) One brass bar and one steel bar are forming the setup shown below. Determine the stresses and the strains in the steel and brass bars when a load of 750 kN is applied to the connection of these two members where modulus of elasticities for steel and brass are Est = 200 GPa and Ebr 125 GPa, respectively, and cross-sectional areas for steel and brass bars are Ast = 700 mm² and Abr = 1000 mm², respectively. 500 mm 400 mm Brass Steel F Fixed Support 2 mm Gap F = 750 KN Fixed Support
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D