3. The concrete column is reinforced by four steel bars of total cross-sectional area 1250 mm². If the working stresses for steel and concrete are 180 MPa and 15 MPa, respectively, determine the largest axial force P that can be safely applied to the column. Use Est = 200 GPa and Eco = 24 GPa. Dimensions in mm -250-

Q: what is meant by laser scanning?

A: Laser scanning is land surveying method that can accurately measure and collect data from buildings…

Q: Explain Types of Cone Penetrometer Equipment.

A: A cone penetrometer is an instrument which used to performing the cone penetrometer test also known…

Q: What the center of gravity

A:

Q: Q:  (i) How to orient a hospital building so that it can get maximum natural light and ventilation.…

A: (1)- The building of hospital should be aligned in east direction as much as possible for maximum…

Q: What are the principles of ultrasonic speed measurement?

A: Explaining the ultrasonic speed: Ultrasound waves are defined as waves with a frequency greater than…

Q: If train conventional equipment, consisting of 10 cars, is traveling at 137 km/h on a curve of 2°,…

A: A mode of transport is a system that uses vehicles, infrastructures and operations of a particular…

Q: 5. und perceptible by humans has frequencies from a) 20 to 2000 Hz b) 20 to 20000 Hz c) 10 to 10000…

A:

Q: he bracket is supported by diameter = 18 mm diameter pins at A and B (the pin at A fits in the 0-35°…

A:

Q: how engineers are responding or making a difference to covid-19 please write it down on a paper

A: Note:- Hi! Thank you for the question As per the honor code, We are not allowed to provide…

Q: . What is the motion of a particle relative to a set of axes which are moving? Dependent Motion…

A:

Q: fluid properties labs

A: Fluid is a liquid which has various properties in it. The various properties of fluid are density,…

Q: What design changes to either the task or equipment could you make that would either compensate for…

A: When it comes to compensating for limitations in human senses or capitalizing on other human…

Q: Define fiber-optic piezometer.

A: A piezometer is a device which is used for measurement of pressure of a fluid in a system or at a…

Q: As Civil Engineering student. Why is it important to know these Alphabet of Lines in your course?…

A: Contractors, estimators, tradesmen, and builders rely totally on technical drawings for the…

Q: in a room size of 30X30 feet, wall mounted visible appliance(s) requried light intensity is answer…

A: According to NFPA 72 2010 and 2013 Edition -    Non-sleeping room - In non-sleeping areas NFPA…

Q: Is this a three moment equation problem

A: The procedure followed is not three moment equation method.

Q: uO 9:1 * Asiacell lin. yols- i docs.google.com 14. Which is NOT a unit of length measurement? Yards…

A: 1.Hear in this question Grads are not units of linear measurements or length measurements, since…

Q: Define Tacheometry.

A: Tacheometry is a term related with surveying. Tacheometry is a method through which horizontal…

Q: 1. WHY DO WE HAVE TO CONSIDER PLUMBING SYSTEM IN A BUILDING DESIGN ?

A: Plumbing system involves laying of pipes (inlet and outlet both), drains, valves and closets, and…

Q: discuss the Applications of Computational fluid dyanamics in the field of civil engineering

A: Fluid dynamics In physics and engineering, fluid dynamics is a subdiscipline of fluid mechanics that…

Q: What are the methods of selecting the equipments?

A:

Q: Discus Astronomy and Engineering

A: The study of space and celestial bodies such as sun, star, and moon etc. and their physical and…

Q: Give a list of some typical situations where ageotechnical instrumentation program is required ?

A: Situations where a geotechnical instrumentation program is required: when Tunnels, boreholes,…

Q: What do you mean by Eddy in the atmosphere?

A: Answer:- Eddy: Small eddies takes place in day time in earths atmosphere, when surface air is heat…

Q: A beam of circular cross section is 3000 mm long and is attached at each end to supports which allow…

A: L = Length of beam = 3000 mm = 3 mP = Offset load = 40000 N = 40 KNσy = Yield stress = 145 N/mm2

Q: Explain with an example the following various obstacles in chaining. .Chaining free, Vision…

A: Types of obstacles in chaining are Chaining free, vision obstructed. Chaining obstructed, vision…

Q: How do sonar or ultrasonic level measurement works?

A: Sonar is a technique for detecting and estimating the distance and direction of underwater objects…

Q: Is it possible to have a better understanding of liquid crystal displays?

A: Liquid crystal displays are used for better quality and improvement. These are very useful in this…

Q: ate unnecessary 6.2 A basic principle of et words. The following writing samples were taken from…

A: We are authorized to answer three subparts at a time since you have mentioned which part you are…

Q: briefly introduce sustainability concepts in design and construction

A: The construction and building industry is a very big and vast industry that involves a very…

Q: Fluid Kinematic classify the fluid motion into four types? write in brief the classification of…

A:

Q: What are Frontal Inversions?

A: Inversion is used when metrological inversion of temperature takes place. It is an alteration from…

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: RADAR stands for a. RAdio Detection And Ranging b. light detection and ranging c. none of above

A: RADAR Stands for

Q: What does cause heat transfer?

A: The creation, utilization, transformation, and interchange of thermal energy (heat) across physical…

Q: What is the measure of position? What is the measure of variation? How do you find the measure of…

A: 1. What is the measure of position? A measure of position is very helpful in determining the…

Q: hi , please help me describe the objects or parts of objects on which Vernier caliper and Micrometer…

A: Vernier caliper and Micrometer screw gauge both are measuring instruments which is used for…

Q: How piezometer units are commonly manufactured?

A: Piezometers are the devices used to measure the static pressure at a specific point or the…

Q: Give one importance of studying Geology for the Civil Engineering Field and elaborate it, thanks!

A: There are some aspects based on which we can get the importance of the geology in civil engineering…

FEA for Dynamic Problems

Finite element analysis or FEA is a computational tool that evaluates the approximate solution for a particular engineering problem. The tools provided by FEA help to evaluate the solutions of partial differential equations (PDEs) computationally following a numerical approach. Solutions of the PDEs can also be performed by following traditional algebraic approaches, but when the problem gets towards the complex side, it becomes very tedious and almost impossible to arrive at the solutions. In such cases, the FEA fulfills the purpose by evaluating the equations following multiple time steps and iterations. The more the time steps and iterations, the more accurate the solution. The solution plotted by FEA analysis and mathematical approaches varies asymptotically.