3. It is desired to design a 5-cylinder aircraft engine with a stroke-bore ratio of 1.2. The piston displacement per cylinder is 85 cubic inches. Determine the bore diameter of each cylinder in millimeters and length of the stroke in millimeters.

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: X 300 mm D 800 mm B

A:

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: 2 m Find the angle theta. a = 5. b = 3. 1m 1m D

A:

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: In the engine system shown, the lengths of the connecting rode (that is the length of BD) and the…

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: What is the resultant force?

A: Let us consider that an object has two forces acts on it. These forces are  10 N to its right.  50…

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: Write the equation that relates applied stress to local maximum stress.

A: Stress concentration factors are generally used to relate applied stress to local maximum stresses.…

Q: Question (2): The length of the-in.-diameter steel wire CD has been adjusted so that with no load…

A:

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: //// // R R J3 Js Jy J. J8 R lt)

A: given; mass of block=mweight of block(w)=mgforce=F

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: If this were to be written how would it look like?

A: Geometric Symbol – This symbol is most useful and shows the position of the dimensions. Diameter…

Q: A hollow tube with thickness t = 1/4 in. is applied with a tensile load of 33 kips. Compute its…

A: Given data,  Tensile load P= 33kips = 33000 lbs  t= 1/4 in  Tensile stress S= 12 ksi = 12000 lb/in²…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.