3. In a quality control system of car parts, samples are extracted from 4 units. Each unit isexamined and the 4 logical signals of the results enter a logical circuit that you want todetermine and whose signals must indicate:a. Whether all samples have been approved. F→₁1(A,B,C,D)b. If the majority has been approved. F→2(A,B,C,D)c. Equal number of approved and disapproved. Fd. Most have been rejected. F→4(A,B,C,D)Perform this logic circuit by means of logic gates so that they meet the 4 conditions.(MSB)(LSB)ABсDCircuitLogical→3(A,B,C,D)F₁F2F3F4

The given block diagram is shown below.4 logical input signals are A, B, C, D.A is the MSB and D is…

3. In a quality control system of car parts, samples are extracted from 4 units. Each unit is examined and the 4 logical signals of the results enter a logical circuit that you want to determine and whose signals must indicate: a. Whether all samples have been approved. F →₁(A,B,C,D) b. If the majority has been approved. F →2(A,B,C,D) c. Equal number of approved and disapproved. F d. Most have been rejected. F →4 (A,B,C,D) Perform this logic circuit by means of logic gates so that they meet the 4 conditions. (MSB) (LSB) A B C D →3(A,B,C,D) Circuit Logical F₁ F2 F3 F4

3. In a quality control system of car parts, samples are extracted from 4 units. Each unit is examined and the 4 logical signals of the results enter a logical circuit that you want to determine and whose signals must indicate: a. Whether all samples have been approved. F →₁(A,B,C,D) b. If the majority has been approved. F →2(A,B,C,D) c. Equal number of approved and disapproved. F d. Most have been rejected. F →4 (A,B,C,D) Perform this logic circuit by means of logic gates so that they meet the 4 conditions. (MSB) (LSB) A B C D →3(A,B,C,D) Circuit Logical F₁ F2 F3 F4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

List the 8051 microcontroller's most important characteristics. Using a clean and well-labeled schematic, go through the basic block diagram of the microcontroller. Introductory course on embedded systems
The desirable static characteristics of measurements system are precision accuracy sensitivity all of these
In ADC, as you increase the number of bits, you can convert analogue signal to digital signal in smaller steps.
Q11) For the following rectifier, how many pulses you are expected at the output? V2 = Vmsinwt 2 V2 Va R. VL - -- Dat а. 3 b. 4 с. 2 d. 6 ترك السؤال ارسال الاجابة
Elashing DC genretou solve in computer line
Arrange the chronological order of the elements and its function to Digital Communication by writing the numbers 1 to 10 in both column A and column B. A Elements Channel Decoder Channel Encoder Digital Demodulator LICHTE SE Digital Modulator Input Transducer Channel Output Signal Output Transducer Source Source Decoder Source Encoder B A ndeseng Function After detecting the sequence, it does some error corrections. A It can be an analog signal. It compresses the data into minimum number of bits. It converts the signal into the original physical form, which was at the input of the transmitter. It does the coding for error correction. It allows the analog signal to transmit from the transmitter end to the receiver end. It produced after the whole process. It takes a physical input and converts it to an electrical signal. The received signal is demodulated as well as converted again from analog to digital.notni erli lo ini arli lo voeber edirsin.sm The resultant signal is once again…
Digital Electronics
(just convert to decimal, don't bother with octal or hex
2. Understand the given Industrial process control system and convert it in to Block diagram (draw neatly) 4-20 mA signal FC 420 mA signal FY FT 3-15 PSI signal FV Pump Pipe InstrumentationTools.com
quiq plz
instruction: answer item 4, 6, and 7 4. Mancio Manufacturing Co. has asked you, as their IE, to check a labor standard prepared by arecently resigned analyst. Determine the sample size you need considering your accuracy is to bewithin 5%, standard deviation of the sample is 1.0 and the mean is 3.0. 6. At ASP Micro Manufacturing, Inc. workers press semiconductor into predrilled slots on printed-circuit boards. Determine the normal time of the operation in seconds. The elemental motions for normal time used by the company are as follows:• Reach 6 inches for semiconductors 10.5 TMU• Grasp the semiconductors 8.0 TMU• Move semiconductor to printed-circuit board 9.5 TMU• Position semiconductor 20.1 TMU• Press semiconductor into slots 20.3 TMU• Move board aside 15.8 TMU 7. The semiconductor used in Costin Calculator has 5 components with the consistency of 90%, 95%,98%, 90%, and 99%, respectively. How reliable is one product of calculator?
Q1: A) Choose the correct answer: 1)----------------- describes the closeness of output readings when the same input is applied repetitively over a short period of time. A) inaccuracy , B) Range , C) Tolerance , D) Repeatability. 2) The element in the measurement system in output takes the form----- -? A) Process unit , B) area . C) Signal presentation unit, D)Application. 3) a good measurement technician can substantially reduce errors at the output of a measurement system by- :? A) Environmental changes, B) system disturbance, C) calculating the effect, D) All . 4) Capacitive coupling, also known as ----------coupling, can also occur between the signal wires in a measurement circuit and a nearby mains-carrying conductor. A) Electromechanical , B) Electrodynamics, C) Electrostatic, D) All. 5) sometimes used to provide shielding from capacitive-coupled noise, but the necessary supports for the conduit provide multiple earth points and lead to the problem of-------? A) Shielding, B)…