3. For the beam shown below draw the influence lines for By, Dy, VC and MC using the equilibrium method. Find the maximum possible value of MC if a 33kN/m distributed load and a single 40KN point load may be placed anywhere on the beam B A E 3 m 3 m 3 m 3 m

3. For the beam shown below draw the influence lines for By, Dy, VC and MC using the equilibrium method. Find the maximum possible value of MC if a 33kN/m distributed load and a single 40KN point load may be placed anywhere on the beam B A E 3 m 3 m 3 m 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 8 mm and a length of L₁ = 2.7 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 25 mm and a length of L₂ = 1.4 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 64 kN is applied to the rigid bar. L₁ (1) Answer: 01 i 02= i L2 (2) (1) MPa MPa
Question 2 The beam shown in Figure 2 supports a distributed live load of 5.0 kN/m and a single concentrated load of P = 10 kN. The dead load on the beam is 2.0 kN/m. Assume A is a pin support and B is a roller support. Use the method of influence lines to determine: (a) The influence line diagram for reactions at A and B; (b) The maximum positive moment created by these loads at C; (c) The maximum positive shear created by these loads at C. D C 8 m 2 m 2 m Figure 2
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 11 mm and a length of L1 = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 21 mm and a length of L2 = 0.8 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 76 kN is applied to the rigid bar.
In the beam depicted above, ?A is a fixed support. The magnitude of ?=365?/?W=365N/m, ?=60?P=60N and all lengths denoted by ?=1.5?a=1.5m. The system is in equilibrium. Using the given sign convention, answer the following questions. a) Calculate the vertical component of the external reaction at ?A in ???????Newtons. b) Calculate the horizontal component of the external reaction at ?A in ???????Newtons. c) Calculate the moment component of the external reaction at ?A in ??????Newton ??????metres. d) Calculate the shear force at point ?B in ???????Newtons. e) Calculate the bending moment at ?B in ??????Newton ??????metres. f) Calculate the shear force at point ?D in ???????Newtons. g) Calculate the bending moment (absolute value) at ?D in ??????Newton ??????metres. h) Calculate the shear force at point ?E in ???????Newtons. i) Calculate the bending moment at ?E in ??????Newton ??????metres. j) Calculate the shear force at point ?H in…
Q1. (а) Figure Q1(a) shows a beam loaded with a point load and a partially UTM uniform distributed load. respectively. support at A and B are roller 3 UTM The M 5 UTM (i) Draw the free body diagram of the structure. * UTM UTM Determine the support reactions at A and B by taking the (ii) structure in equilibrium condition. ITM O UTM - UTM 5 UTM O UTM 30kN 30° 10KN/m F = 840 N 2m 24 m 2m 4m A \3 m G UTM 15 m 2 m STMUTM 5 UTM FIGURE Q1(a) 10 ni FIGURE Q1(b) 一

A cross-section is subjected to a maximum shear of V=160 kN (see figure): Determine the centroid of the cross-section. Calculate the moment of inertia (I) of the cross-section. Determine the shear stress at point A in the cross-section.
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
Problem 1: The figure shown is a beam subjected to varying loadings and a point load. a) Determine the magnitude and direction of the single equivalent force to the forci shown. Specify its location on the beam from point B. b) Calculate for the support reactions at A and R Fi 17kN 4kN/: 7.9 kN/m -5 m 6.7 m 2.8kn
For a figure shown, a. Draw the influence for reaction at A. b. Draw the influence for Shear At C c. Draw the influence for moment At C. d. Determine the maximum values of these functions for a moving uniform distributed load of 5KN/m. ( Show complete solution.)
Draw the influence lines when a = 3 b = 3 c = 2 d = 2
For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo В a
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 8 mm and a length of L₁ = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 16 mm and a length of L₂ = 1.0 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 66 KN is applied to the rigid bar. L₁ A B Answer: 0₁ = i 38 02 i L2 (2) (1) (1) MPa MPa