3. Find resultant torque about Find resultant torque about axis A for the arrangement shown below 30 N negative 20 N 300 300 6 m 2 m 4 m 40 N

Q: rds, discuss five applications of manut ring.

A: Nowadays CIM is used  in automatic manufacturing. It has high accuracy and precion. G code and M…

Q: Task 3 A hot water pipe that is used for domestic applications of 0.12 m outside diameter is…

A: Given Diameter of outside =0.12 m Ts,1=800 K Ts,2=490 K

Q: Select all flow visualization techniques for gas flow at 1500m/s at sea level, among them, which can…

A: The skill of making flow patterns visible is known as flow visualization. Because most fluids (air,…

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A:

Q: Task 3 Evaluate the performance of a four-stroke, six-cylinder Diesel cycle, the cylinder bore is 10…

A:

Q: For this case of beam bending, what is the internal bending moment at x = 0.2 m if P=98.8 N and…

A: According to the given dataA loading beam ABP=98.8 NL=1.0 mx=0.2mWe need to findThe internal bending…

Q: Searbox and compound train gear system are widely used in power transmission systems to change input…

A:

Q: rio 1 ignition engine that operates on an ideal Otto cycle has a compression ratio of 8. At th g of…

A: Internal combustion engine It is a device which used to convert chemical energy of fuel into heat…

Q: Part (1): 3 kg wheel has an outer radius of 450 mm rolls down an incline starting from rest. The…

A:

Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…

A: given; diameter of solid shaft(ds)=4.2in                                       =0.1068mweight of…

Q: Show from the following data taken for the automobile test performed on a 4 cylinder gasoline engine…

A:

Q: a. Find the State Variable model, in Matrix form, for the system shown in Figure 2. M1 K1 M2 K2…

A: Given State variable model FBD- ...... a ......b For figure a Ma=∈Fnet M1x1¨+bx1˙+k1x1=0 … c For…

Q: The cable exerts a tension of 2 kN on the fixed bracket at A. Write the vector expression for the…

A:

Q: OII, : (20e-0.61) rad/s², where t blade an angular acceleration a = is in seconds. Determine the…

A: Given:α=20e-0.6t rad/s2t=3 sec

Q: Q3: Find the transfer function G(s)=X3(s)/F(s) for the translational mechanical system shown blow 2…

A:

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400…

A:

Q: the nodal displacements are For the plane strain elements shown in the Figure given as (4, 4) uj =…

A: Solution: Given Data:

Q: Q2. For the given continuous beam draw V(x) and M(x) diagrams. A 12 in.- B 800 lb 6 in. C D Hinge 12…

A:

Q: answer with explanation in handwritten format

A: Given Solidworks option To find Function and explanation Solidworks is asoftware used for modeling…

Q: Five lbs of propane is contained in a closed, rigid tank initially at 80 lbf/in.2, 150°F. Heat…

A: Given:Mass of propane, m=5 lbsPressure of propane in the tank, P=80 lbf/in2Initial temperature of…

Q: You are required to perform the following tasks: 1. Sketch a 3D view to show, the ship, spin-axis,…

A: Whenever the axis of rotation (or) spin of a body changes its direction , a gyroscopic couple must…

Q: Firefighting job requires a special clothing, a protective clothing is typically constructed of…

A: Heat transfer through wall is given by, Where, Q = heat transfer rate in watt A = area in m2 dT =…

Q: 2. A pressure vessel 300 mm in diameter is to be fabricated from steel plates. The vessel is to…

A:

Q: spring is suspended vertically I Tixed support. Thể spring has spring cðhstaht k = ttom of the…

A: givenspring constant k=48N/mmass of object m=16kgdamping constant =β N/m s

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A:

Q: Question 2 A small object of mass m is released at the rim of a smooth semi-spherical bowl of radius…

A:

Q: 1. Stability and determinacy of structures: give the three sets of criteria of stability and…

A: One who disturbs a stable building will not cause it to fall. In general, there are numerous…

Q: 2) Consider a copper-nickel (Cu-Ni) alloy composed of 45 wt% Ni:55 wt% Cu that is at equilibrium at…

A:

Q: Problem B-6-19 Consider the de servomotor shown in Figure 6-85. Assume that the input of the system…

A:

Q: Scenario 2 A compression ignition engine that operates on an ideal diesel cycle has a compression…

A: Engine: Engine is a device which useful for conversion of chemical energy of fuel into heat energy.…

Q: Twenty gpm of 60°F water enters the parallel piping system shown in the figure. Branch A consists of…

A:

Q: An oscillating water sprinkler is operated at point A on an incline that forms an angle B with the…

A: Consider the right side part to calculate the distance RB. AB-direction…

Q: Problems 1.85 through 1.92 refer to a linkage that is to act as a crank-rocker mechanism Link…

A:

Q: Explain the installation procedures of a flexible coupling

A:

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R, and R₂. The…

A: Given data: ● The load applied on the beam: W = 13 kN ● The diameter of the beam: d = 25 mm ● The…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.