Solve with all the steps in detail and draw properly 3. Draw the energy band diagram of a PN junction diode under reverse bias condition. Explainhow the applied voltage affects the conduction band, valence band, and Fermi levels onboth sides of the junction.

Energy Band Diagrams of an npn BJTNo Bias Condition Fermi Level: The Fermi level is the energy level…

Answered: 3. Draw the energy band diagram of a PN…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What will be the value of the reverse saturation current for a Si diode operating in forward bias mode. The following information is given: Diode current 3 A Voltage across diode 0.25 V. Temperature is 300 K.
Plot the I-V characteristics of a PN junction diode (linear and log scale) for different temperatures and plot the characteristics. Explain the observed behavior.
In reference to the output waveform below and using ideal diode model: Vout +7.5V -3.5V a. Analyze the behavior of the circuit and fill up the table below. Vin Diode state Vout (FB or RB) +6V OV -3V -6V b. Draw the clipper circuit that will produce the given output waveform.
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
1. Draw the output voltage waveform for each circuit in Figure below and include the voltage values. N +5V +50V Vin R Va R o 0% Y 9 33k 5 Vo -5V -50v I I (@ () a. Whatis the peak inverse voltage across each diode in Figure above? b. What is the peak forward current through each diode in Figure above?
2.Sketch the waveforms for the load current and load voltage for the circuit show in Figure 2. Show the peak values. Use the offset diode model in your calculations. Input voltage source could be represented as a sine waveform, given as Vin=20sin(wt +30), and RL = 20 S Figure 2 www R₁ Vout
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.
For a Silicon diode, the forward current is 109 times the reverse saturation current Is. What will be the value of the forward diode voltage? Assume eta to be 1.
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=3 V and V2=8 V. R www D2 DI Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform
Consider the given choices

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

3. Draw the energy band diagram of a PN junction diode under reverse bias condition. Explain how the applied voltage affects the conduction band, valence band, and Fermi levels on both sides of the junction.