3. Consider an RC circuit with R = 100, C = 0.1, and Eo = 0. Suppose that the initial charge on the capacitor is Q(0) = 50 and the switch is closed at time t = 0. (a) Find the charge for t≥ 0. (b) Compute the current I(t) = Q'(t) for t > 0. (c) What is the "jump" in the current at t = 0.

3. Consider an RC circuit with R = 100, C = 0.1, and Eo = 0. Suppose that the initial charge on the capacitor is Q(0) = 50 and the switch is closed at time t = 0. (a) Find the charge for t≥ 0. (b) Compute the current I(t) = Q'(t) for t > 0. (c) What is the "jump" in the current at t = 0.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The current in a 0.6 microfarad capacitor is 0 [A] for time less than zero and 3cos50000t [A] for time greater than or equal to zero. Find v(t) and the maximum power delivered to the capacitor.
If in a circuit, E=9v and the current I reaches half its maximum value of 2A at t=0.1s after the switch is closed. What is the time constant of the circuit? What is the emf across the inductor at t=0.1s?
An LC circuit like that in the figure below consists of a 3.30-H inductor and an 836-pF capacitor that initially carries a 118-μC charge. The switch is open for t < 0 and is then thrown closed at t = 0. Compute the following quantities at t = 5.00 ms. 2max 000 (a) the energy stored in the capacitor (b) the total energy in the circuit (c) the energy stored in the inductor 0
Can you help me solve this? For two capacitors C1, C2 in series, with initial voltages (at t = 0-) V01 and V02, respectively, derive the instantaneous voltages v1(t) across C1 and v2(t) across C2 for t ≥ 0+in terms of C1, C2, V01, and V02.
-In the circuit shown on the right the switch S has been open for a long time. What is the current flow through the inductor (0, 2 to 1, or 1 to 2) ? -In the circuit shown on the right the switch S has been open for a long time. At the instant the switch S is closed, the current flow through the inductor is (0, 1 to 2, or 2 to 1)? -In the circuit shown on the right the switch S has been open for a long time. The current flow through the inductor is (increasing, steady, or decreasing)? -In the circuit shown on the right the switch S has been open for a long time. Immediately after the switch S is closed, the current flow through the inductor is (increasing, steady, or deacreasing)? -In the circuit shown on the right the switch S has been closed for a long time. The current flow through the inductor is (1 to 2, 2 to 1, or 0)? -In the circuit shown on the right the switch S has been closed for a long time. At the instant the switch S is opened, the current flow through the inductor is (1…
The circuit contains two capacitors in series and two resistors in parallel with each other connected to an ideal source with e = 50V. Initially, the capacitors are empty, then at t = 0 the switch is closed. Given R1 = 7.02, R2 = 82, C = 6.0F, and C2 = 8F а. what is the voltage, as a function of time, across C1 and C2? b. What is the current, as a function of time, through R1 and R2? Ce R2
About the circuit below: a) How long does it take for the current in the inductor to reach 40% of its maximum value? b) After 1 time constant in the closed position, the switch is opened at t = 0. Find the current and voltage in the inductor when t>0. c) Sketch the behavior (waveforms) of voltage and current in the inductor and resistor R2 in the storage and discharge (decay) phase of the inductor. R1 = R5 = 55k Ω R2 = R4 = 20k Ω R3 = R6 = 25k Ω V = 2500 v L1 = 50 mH
The switch in the figure below is open for t < 0 and is then thrown closed at time t = 0. R 2R ww www www (a) Find the current in the inductor. (Use the following as necessary: L, R, t, and for E.) 12- (b) Find the current in the switch as functions of time thereafter. (Use the following as necessary: L, R, t, and & for 8.) switch
All capacitors were initially discharged.at t = 0, S1 is placed at position 1 and S2 is closed.At t = 15 ms, S1 is placed at position 2 and S2 is kept closed. At t = 25 ms, S1 is kept at position 2 and S2 is opened.after 25 ms, the voltage vT will Question options: increase until it reaches the battery voltage at steady state exponentially decay to zero stay constant be a sine wave
Need help with a and b
5. An RC (DC) circuit consists of a Resistor with a resistance of 25000 SQ and Capacitor in series with a source potential of 30.0 V. The capacitor is initially uncharged and the circuit is completed at t= 0. a) If it is to take 45.0 seconds for the capacitor to be 88.0% fully charged, what must the be capacitance? b) At what time is the potential difference across the capacitor 17.0 Volts?
A capacitor is connected to an electrical circuit as shown in the image. The initial voltage of the capacitor will be that obtained when fully charged with all four switches closed. Then the switches that are required for it to start downloading are opened. It is known that after 0.1 s in its discharge process, the voltage on the capacitor is 20% of the voltage it initially had. Questions: 1. Explain how the initial voltage of the capacitor can be calculated.2. Calculate the initial voltage of the capacitor before it begins to discharge.3. Say characteristic switches are necessary to initiate the discharge of the capacitor and why.4. Calculate the value of the capacitance.