3. Commercial hydrochloric acid and sodium sulfate are produced by the reaction: NaCI + H20 + SO3 = Na,SO4 + HCI The reaction is carried at 482°C. After separation of the Na,sO, the HCI is to be absorbed in water. Per 1000 kg of sodium chloride charged, how much Na,SO, and 87% by wt aqueous hydrochloric acid solution are obtained if the reaction goes to 90% completion? If the SO, is supplied 20% in excess and H20, 100 % in excess of the theoretical amount, how much 98% sulfuric (SO3and H;O) and fresh water should be fed to the reactor?

Q: Q2/ Based on your knowledge in atomic bonding and structure, give some typical examples showing that…

A: Atomic bonding Atomic bonding is the process in which molecules and atoms do interact. They are also…

Q: Q4 A) Give short notes about Heat Transfer Mechanisms within supported formal and illustrated…

A: Heat Transfer Mechanisms: Conduction: The process in which transfer of energy exchange takes place…

Q: Flash distillation is normally carried out in which mode?   a Batch   b Continuous

A: This question is based on distillation. We will analyse each option and find out the correct option.

Q: electricity by using solar furnace

A: solar furnace classified as renewable source of energy and belongs to solar concentrator power…

Q: Explain Semibatch process?

A: In a batch process, the desired product comes out of the reactor in groups i.e. in discrete amounts…

Q: What are the Safety inspections. [Important exams, checklist, and inspections] for diaphragm pump?

A: The safety inspections for the diaphragm pump are to be mentioned.

Q: LS633-LS108 OD: 7+ @ 190–532NM, OD, 6+ @ 1050–1064NM - O.D. 4+ @. 10,600NM

A: Laser safety eyewear has specific lenses that absorbs and reflect the perticular wavelength to…

Q: What is the difference between cool-side ESP and hot-side ESP?

A: The difference between the cool-side ESP and the hot-side ESP is to be mentioned.

Q: Could you please show me step by step how you get the 40 uL on the attached? Thank you.

A: Given that the equation of step is : C1V1 = C2V2 Now, value of C1 is taken= 10000 cell/1000 uL,…

Q: The oxidation of mercury is a benefit in FGD scrubber. Why?

A: FGD scrubber is a flue gas desulfurization wet scrubber which is used to capture the flue gases…

Q: Draw the diagram of an reboiler ONLY of Amine Sweetening process in a Central Processing Plant?

A:

Q: Name 3 secondary refinery processes and explain their main purpose.

A:

Q: Principal of mass transfer

A: Pricipal of mass-transfer:

Q: Sort the following models according to an API value: 40 oil, kerosene, oil 40, gasoline, oil 150,…

A: To sort the given list of oils as per their API values

Q: What if you were asked to design a tubular vessel that would minimize dispersion? What would be your…

A: The correlations between Re and Da can be used to determine Da which in-turn will give the…

Q: Explain Process of extraction oil lubricant about description and conditions process

A: A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which…

Q: Make a comparison between trays & packing distillation column , advantage and disadvantage should be…

A: In the distillation column with trays, there is the liquid holdup in the tray that provides…

Q: Give 5 mineral families that used in engineering activities, and how are they used ing engineering…

A:

Q: What is the q-line and how is it related to the feed condition?

A: The definition of the q-line is to be mentioned along with its relation with the feed condition.

Q: How do pressure-swing and thermal-swing adsorption differ? What are inert-purge swing and…

A: The difference between pressure swing adsorption and thermal swing adsorption is to be mentioned.…

Q: what is a rich/lean heat exchanger ? and how will an increase in pressure drop affect it ?

A: It is required to explain a rich/lean heat exchanger.

Q: 3. list as many factors as you can think of that will affect a house's heating/cooling needs.…

A:

Q: (a) When rinsing clothes, would it be more efficient to divide the water and rinse several times, or…

A: Let,   The mass of dry cloth that is insoluble be ‘FA’ The mass of soluble dirt be ‘FB’ The mass of…

Q: Calculate the consistency index Kand apparent viscosity at shear stress= 300kPa. Classify the…

A: A solution is given τyx×10-3kgms2 -dνxdy1s 50 50 100 71 150 87 200 100 300 123 400…

Q: Calculate the mass of beef and back fat for the preparation of 100 kg of sausage. The beef contains…

A:

Q: 14. A smaller absorption factor means an increased driving force for absorption. [……..] 15.…

A:

Q: Outline FIVE (5) factors which can influence the effectiveness of solvent extraction.

A: Solvent extraction: It is a process where it is separated the compounds based on the solubility's…

Q: Calculate thestolng duty reguivre to condenserdn acetove from

A: Given:   The pressure of the system, P = 1 atm Molar flow rate of acetone, n = 100 kg-mol/s The…

Q: 3- List two reason, to keep low pressure drop across the production system.

A: Hi, since you have posted two questions, we are allowed to answer only one per submissions according…

Q: Explain what information a material safety data sheet contains and why it is important for employee…

A:

Q: What Risky-Safety Analysis is conducted during the siting of Filling/Gas Station

A: A filling station is a place where the petrol or the gas is stored, and fill the vehicles when…

Q: What is meant by hydraulics optimisation?

A: Given a term  hydraulics optimization Find What is meant by hydraulics optimization ?

Q: What is Ionization Energy ? Why it is used ?

A: The definition of ionization energy is to be mentioned along with its use.

Q: A food is initially at a moisture content of 90% dry basis. Calculate the moisture content in wet…

A: Given:  Moisture Content in Dry Basis = MCdb = 90% = 0.9  Moisture Content in Wet Basis = MCwb we…

Q: Create a  five problem about humidification

A: Five problem about humidification

Q: xplain about Stoitless Steel heat treakment-prasess (aunealing normsalizingn and hardRning)e

A: Heat treatment processes like annealing, normalising and hardening are

Q: What is the need for energy balance in process design? Explain

A: Energy balance  is expressed as -all energies into the system are equal to all energies leaving the…

Q: Wood chips are to be dried in a rotary drier from 35% moisture to 12% moisture. If 10 kg of wet wood…

A: Given that, Inlet Mass flow rate of wet wood = 10 Kg/min Moisture in wet wood = 35% Moisture in dry…

Q: What is the importance of booster station during oil gathering? Note: write with type written

A: The booster pumps or the compressors are located at different intervals along the length of a…