3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kg 20.01%, 2667.84 , 1715.88. ,955.97 3.74, 951.96 K , 35.68%, 3.78- kJ kg kg kWh kg kg

3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kg 20.01%, 2667.84 , 1715.88. ,955.97 3.74, 951.96 K , 35.68%, 3.78- kJ kg kg kWh kg kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a 150-MW steam power plant that operates on a simple Rankine cycle. Steam enters the turbine at 7 MPa and 500°C and is cooled in the condenser at 10 kPa. Calculate the thermal efficiency of the plant. Assume an isentropic efficiency of 87% for both the turbine and the pump
Problem 2 Consider a reheat Rankine cycle utilizing steam. Steam leaves the boiler and enters the turbine at 600 psia, 800 °F. After expansion in the turbine to 60 psia, the steam is reheated to 800 °F and then expanded in the low-pressure turbine to 1 psia. After presenting a schematic of the problem in addition to clearly labeled and explained T-s and h-s diagrams, you are asked to determine the following: (a) Pump work required per Ibm of working fluid. Quality of fluid at turbine inlet. (b) (d) (e) (f) Work output of turbine per Ibm of working fluid. Energy input to the boiler per Ibm of working fluid. Heat rejection by the condenser per Ibm of working fluid. Determine the cycle thermal efficiency.
Consider a steam power plant, which can be modeled using the ideal reheat Rankine cycle. The steam entering the high- pressure turbine is at 6 MPa and 400 degrees C and leaves at 2 MPa. The steam is then reheated to 400 C at constant pressure, before it expands to 20 kPa in the low-pressure turbine. Calculate: (a) the turbine work output in kJ/kg (b) the thermal efficiency of the cycle
This is an Open feedwater not a closed feedwater thank you
Consider an ideal Rankine cycle with reheating as shown. Steam enters a high-pressure turbine at 6 MPa and 440°C and expands to 0.5 MPa then reheated to 400°C. The condenser pressure is 8 kPa. • Calculate the quality at the exit of the low-pressure turbine, x6 = • Calculate the work produced by the low-pressure turbine in kJ/kg • Calculate the heat transfer in reheating (greheat) in kJ/kg = Boiler Turbine 3 QH 5 Condenser 87.3% || 89.0%||| 91.1% | 94.3% || 95.9% || 99.0% 763 |805 || 832 || 851878 || 901 513 556| 581 665 | 697|| 758
In the ideal Rankine cycle shown, the boiler pressure is 6 MPa and the condenser pressure is 8 kPa. The steam enters the turbine at 440°C at a mass flow rate of 7.0 kg/s. In your written solution, (a) determine the enthalpies at states 1, 2, 3, and 4; (b) draw the T-s diagram with the states in the correct region; (c) determine the cycle power output; and (d) the cycle thermal efficiency.
Please show the solution. Thank you very mmuch
QI) Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of 45 MW. Steam enters the turbine at 6 MPa and 500°C and is cooled in the condenser at a pressure of 20 kPa by running cooling water from a lake through the tubes of the condenser at a rate of 2000 kg/s. Show the cycle on a T-s diagram with respect to saturation lines, and determine: The thermal efficiency of the cycle?
A simple ideal Rankine cycle with water as the working fluid operates between the pressure limits of 3 MPa in the boiler and 30 kPa in the condenser. If the quality at the exit of the turbine cannot be less than 80 percent, what is the maximum thermal efficiency this cycle can have? Use steam tables. The maximum thermal efficiency is %.
A simple steam power plant uses water as the working fluid and operates on the simple ideal Rankine cycle. The boiler operates at 15000 kPa and the condenser at 30 kPa. Show the cycle on a T-s diagram with respect to saturation lines and determine the phase change in each state, the minimum temperature required at the turbine inlet such that the mixture at the exit of the turbine is not lower than 80 percent and the thermal efficiency of the cycle
3) An ideal Rankine cycle with superheat and reheat has steam entering the turbine at 10 MPa and 440 °C. The steam is extracted and sent to the reheater at a pressure of 1.5 MPa, and returns to the turbine at 440 °C. The condenser pressure is 20 kPa. The cycle produces 400 MW of net power. Determine (a) the qualities of steam at (i) high pressure turbine exit, and (ii) low pressure turbine exit (b) the thermal efficiency, in % (c) the rate of heat transfer, into the working fluid as it passes through the boiler, in MW (d) the rate of heat transfer, from the condensing steam as it passes through the condenser, in MW (e) the mass flow rate of the condenser cooling water, in kg/ h, if cooling water enters the condenser at 12 Cand exits at 37 C