Answered: 3. A small circular hole 6.00 mm in… | bartleby

Related questions

Question

100%

3. A small circular hole 6.00 mm in diameter is cut in the side of a large water
tank, 14.0 m below the water level in the tank. The top of the tank is open to
the air. Find (a) the speed of the water coming out from the hole, and the
volume discharged per second.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

1. Fluid Flow: Water runs into a fountain, filling all pipes, at a steady rate of 0.750 cubic meters per second. How fast will it shoot out of a hole 4.50 cm in diameter?
If it takes 2.15 min to fill a 23.0 L bucket with water flowing from a garden hose of diameter 3.10 cm, determine the speed at which water is traveling through the hose. If a nozzle with a diameter two-fifths the diameter of the hose is attached to the hose, determine the speed of the water leaving the nozzle.
2. Water flows through a fire hose of diameter 6.35 cm at a rate of 0.012 m³/s. The fire hose ends in a nozzle of inner diameter 2.20 cm. What is the speed with which the water exits the nozzle?
A water pipe having a 2.59 cm inside diameter carries water into the basement of a house at a speed of 0.770 m/s and a pressure of 213 kPa. If the pipe tapers to 1.31 cm and rises to the second floor 6.71 m above the input point, A) What is the speed of the water at the second floor? B) What is the water pressure at the second floor?
Hot water with a density of 980 kg/m3 flows through a 51.2 mm diameter round pipe at 1.25 m/s. What is the mass flow rate (in kg/s) of the water How many significant figures should be used in the final answer?
A liquid is flowing through a horizontal pipe whose radius is 0.0301 m. The pipe bends straight upward through a height of 8.80 m and joins another horizontal pipe whose radius is 0.0726 m. What volume flow rate will keep the pressures in the two horizontal pipes the same? Number Units 202
4.0 mm 16. Consider the following diagram. (let air be an ideal, incompressible fluid) 2.0 cm 1200 cm'/s a. If the air is found to have a flow rate of 1200 cm3/s as it leaves the 4.00 mm diameter pipe, what is the velocity of the air in both segments of the pipe? b. If the density of air is 1.28 kg/m3 and the end of the pipe on the right opens up to the atmosphere, what is the pressure of the pipe at the 2.00 cm diameter section? C. If the fluid in the bottom of the U-tube is mercury with a density of 13,600 kg/m3 what is the difference between the surface levels of both sides of the tube, marked as h in the diagram?
A typical pressure in a vein is 18 mm Hg. How high would you need to hang an IV bag so that the fluid enters the blood stream at this pressure? Assume the IV fluid has a density of 1000 kg/m3. A nozzle with an area of 0.3 cm2 is attached to a garden hose with an area of 1.5 cm2. The flow rate through the nozzle is 0.12 L/s.What is the speed of the water in the hose in cm/s? (1 L= 1000 cm3) What is the speed of the water in the nozzle in cm/s? (1 L= 1000 cm3)
Oil (p = 920 kg/m³) is flowing through a pipeline at a speed of 1.88 m/s. If the diameter of the pipe is 0.16 m, what is the %3D mass flow rate? kg/s
A horizontally oriented hypodermic syringe has a barrel diameter of 1.2 cm and a needle diameter of 2.4 mm. A plunger pushes liquid in the barrel at a rate of 4.0 mm/s. Calculate the flow rate of liquid in both parts of the syringe (in mL/s) and the velocity of the liquid emerging from the needle.