3. A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 5kN. Find the minimum factor of safety using Maximum shear stress theory. All dimensions are in mm. -500 25 D. 7 +20 -35 D. -180 -3 R. -280- -175- -50 D. -25 D. -20

Q: What are the general equations of plane stress transformation?

A:

Q: The image shows the yield loci for the Tresca and von Mises yield criteria. Between which two points…

A: GIVEN: TO FIND:

Q: What do you mean by fatigue failure of machine parts? Explain briefly. Give an example of a thing or…

A: Fatigue Failure

Q: A 30 cm long, 12 mm diameter carbon steel rod was subjected to 15.5 kN of tension. Calculate:  (a)…

A: Given Applied load = 15.5 kN  Length = 30 cm Diameter = 12 mm To find Stress Strain Change in…

Q: Define different types of stresses, strains and material constants.

A:

Q: Define the term lateral normal strain.

A: Strain is defined as the ratio of change in length upon original length .   Strain are of two type :…

Q: Explain the differences between a ductile material and brittle material. Also, draw their…

A: DUCTILE MATERIALS: 1. Ductile material are those which undergoes large plastic deformation under the…

Q: 2.20. The uniaxial yield strength of annealed AISI 1015 steel is 386 MPa. Estimate the shear stress…

A: Given data: It is required to determine the shear stress according to the Tresca’s theory and…

Q: How can we apply the general equations of plane stress transformation?

A: An object is under a biaxial state of stress when the stress exists only inside the 2-dimensional…

Q: The critical resolved shear stress for a metal is 33 MPa. Determine the minimum stress necessary to…

A: Given Data

Q: Uniform and non uniform stress, gives proper solution explanation with diagrams.

A: Given data Uniform and non uniform stress, gives proper solution explanation with diagrams.

Q: 3. Explain the concept and the relationship between state of stress at a point and transformation of…

A:

Q: Describe the Maximum Normal Stress Theory?

A: The Maximum Stress Theory is one of the failure theories postulated by Rankine. Hence this theory is…

Q: Identify the indirect force in the following Select one: O Tensile O Both Tensile and Compressive O…

A: Solution:

Q: Explain the deconvolution of the principal stress state into the hydrostatic and deviatoric stress…

A:

Q: Q5 It was found experimentally that a certain material does not change in volume when subjected to…

A: when a body is subjected to elastic state of stresses, then the strain in the three mutual…

Q: A 3 meter long solid cylindrical rod has a diameter of 50 mm. The rod is subjected to a compressive…

A: Given Data P=500N dia=0.050m E=500Gpa area=3.14(0.025)2=0.0019625m2 stress=5000.0019625=0.254Mpa…

Q: Explain in detail c the soil layer. Use

A: At a point inside a soil mass, stresses will be created as a result of the soil lying over the…

Q: A socket of above knee amputee is used in the following analysis. It may considered as cylinder with…

A:

Q: What is Shear Stress and explain with example?

A:

Q: Consider a metal rod with a critical resolved shear stress of 40 MPa for a specific crystallographic…

A: Given:The critical resolved shear stress = The angle between the normal to the plane and the applied…

Q: the shear yield stress

A: Given; The uniaxial yield stress of a material is=300 MPa Acc. to Von Mises criterion,  Determine…

Q: One of the applications related to strain energy is Bow and arrow Explain how this is related to the…

A: Strain energy is the energy stored in a member due to deformation. It is the energy absorbed by a…

Q: Discuss the engineering applications of thermal stresses.

A: Thermal stress: The stress induced in any object due to the change in its temperature is known as…

Q: Derive and Express the relation of strain transformation in detail.

A: Given A body under 3D loading To find Strain transformation explanation

Q: CApans the temperature increase it would that number from the temperature er this contact and…

A:

Q: Part-A (Theoretical & Mathematical Problem) For the following state of stress, (a) using the general…

A: (a) Write the given stresses from the diagram.   σx=20 ksiσy=-10 ksiτxy=-12 ksi   Write the angle…

Q: Using Mohr's circle (no credits otherwise), solve the following questions: (a) the principal…

A: Do the following steps in order to draw the Mohr's circle for the given state of stress. 1. Draw two…

Q: 3. A 30-cm long, 12-mm diameter carbon steel rod was subjected to 15,5 kN of tension. Calculate (a)…

A:

Q: 1 A rod of a certain material is 50 mm in diameter for the first 100 mm and 25 mm in diameter for…

A: Given data:Rod 1:Diameter, D1 = 50 mm = 0.05 m for first 100 mm lengthL1 = 100 mm = 0.1 mDiameter,…

Q: For the curve shown elow, energy tố đestroy the specimen. Use any method but your solution must…

A: The above diagram represents the Force applied to the specimen and relevant elongation. It is…

Q: A 3D solid component is subject to external forces such that following three principal stresses are…

A:

Q: Q1-. A 1m long metal is stretched so that it increases in length incrementally in four passes by an…

A:

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in…

A:

Q: Define plane stress and plane strain, making clear which, if any, of the stresses are zero in each…

A: Plane stress If a plane is undergoing load and at any point, the normal stress vector is zero (the…

Q: A cylindrical tensile specimen (undeformed radius is 5mm) is subjected to a tens load F. The…

A:

Q: clearly explain the terms linear strain and shear strain,what do they measure,how are they different…

A: Linear strain occurs due to normal force and shear strain occurs due to tangential force.

Q: From the consideration of the stress element, the shear stresses at x-plane and y-plane must be: of…

A: There is a stress element which is in the equilibrium condition. so all the net external forces and…

Q: Q5) material given the data from a tension test ? How would you determine the strain- hardening…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.