3. A fluid is flowing in a 150-mm-diameter pipe with a velocity of 2.50 m/s. The fluid pressure is 35 kPa. The elevation of the pipe's center above a given datum is 5.0 m. Determine the total energy head if the fluid is (a) water, (b) ammonia with a specific gravity of 0.83, (c) gas with a specific weight of 12.5 N/m.

Q: Piston Pum 0.12 m saline 0.3 m

A: The work done in a piston cylinder assembly can be determined using the formula given below as-…

Q: A pump delivers water, density =1000kg/m3, at a volume flow rate of 0.004256 m3/sec.  If the head…

A: Given:Water density, ρ=1000 kg/m3Volume flow rate of water, Q=0.004256 m3/secHead developed by the…

Q: Water enters a turbine through a 320mm diameter pipe at the rate of 215 lit/s at a pressure at A of…

A: given data  diameter at A = 320mm flow rate = 215 lit/s pressure at A = 150kpa pressure at B = -35…

Q: 5. A generator produces electricity from a water tank as shown. Determine the electrical output from…

A:

Q: Water at 10°C is flowing steadily in a 0.12 cm diameter, 15 m long horizontal pipe at an average…

A: For solution refer below images.

Q: A 20-KW motor with 80% efficiency drives a centrifugal pump delivery 0.08m3/sec against a head of…

A: Introduction The efficiency of the pump consequently, is never more than a hundred percent since…

Q: Air enters the circular nozzle with a velocity of 32 m/s and then exits to the atmosphere at B.…

A: Given:Velocity at A,VA=32msDiameter at section A,DA=0.4mDiameter at section B,DB=1.2mCross sectional…

Q: 5) The power input of the pump is 10 kW and the friction head loss between A and B is 1.25 m, as…

A:

Q: Water is ejected vertically from a pressurized tank as shown in Figure 2. The "3 atm" pressure value…

A:

Q: What is the velocity of the pipe center (m/s)? Given that h3%-88.3 cm h3 h2 =7 cm h =3 cm] Water

A: hps=88.3+7hps=95.3 cm or 0.953 mhp=7 cm or 0.07 m apply bernoulli's equation between 1 and…

Q: Water flows at 10 m/s through a pipe. The pipe's radius then becomes 40% of its original size. What…

A: According to the  given data First pipe radius  =R with velocity v=10m/s Second piperadius=r=0.40R…

Q: A fluid is flowing with average speed 5.0 meters/sec in a 10 cm inner diameter pipe. Determine the…

A:

Q: Problem 5: A pressurized tank of water has a 10-cm-diameter nozzle at the bottom, where the liquid…

A: Taking point 1 above liquid surface and point 2 just after nozzle exit.

Q: 141 litres of water flows through a pipe of 0. 3 m diameter per second. The average flow velocity in…

A: Given data:- Flow rate(Q) = 141 L/s = 0.141 m3/s Diameter of pipe(D) = 0.3 m The average flow…

Q: efficiency (expressed in decimals, such as 0.25; don't write 25%) of the pump is ?

A: Need to find efficiency of pump.

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.