3. A flange compressive coupling is used to connect a driving electric motor to a reduction gear box of a machine. The motor has an output of 80 KW at 1000 rpm. Work required c. Complete design calculations for the coupling parts (shaft, split cone, flange, tightening bolts). 1. d. Complete assembly drawing for the coupling.

Q: I need a literature review ten determinationon with ten reference using google just puting the links…

A: Enhancing indoor air quality and safe entertainment in sports halls

Q: dy 35+メ9

A: The provided differential equation is given as, dydx=3y2+xyx2

Q: xplain how each of these variables relate to environmental impact assessment and how they  affect…

A: Environmental Impact Assessment (EIA) is the process of analysing the possible environmental…

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: If FB = 560 N and Fc = 700 N, determine the magnitude and coordinate direction angles of the…

A:

Q: The circular rod shown in Figure 4 is subjected to a torque of 2000 kNm. Find maximum shear stress…

A: (a) The maximum shear stress in the shaft is 10185.9 MPa. (b) The rotation of the free end of the…

Q: Perform FMEA and Root Cause Analysis for any TWO problems faced in your industry.

A: introduction; FMEA is a failure mode and effect analysis. FMEA quality tools enhance the quality of…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: Tstall Wno load w

A: given data: linear relationship between torque and RPM. T(stall) =0.001Nm RPM=10500 To find: max…

Q: Determine, using the principle of superposition, the reactions at supports A and B for equilibrium.…

A:

Q: Particles less than in diameter are generally referred to as the fine mode: a. 0.75 μm; b. 7.5 um;…

A: This question is based on the concept of size of particles.

Q: OA F >F>F OE- F = F, F, >F, >F, F > F, >F, D) OF> F >F,

A: Forces on the surfaces, F1,F2,F3 Area of each surfaces, 2S,S,3S

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: A ballistic pendulum consists of a 3.3-kg wooden block originally at rest, 0 = 0°. When a 2-g bullet…

A:

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: find the length of (20mm) diameter bore is equal to that in the (30 mm) diameter bore,

A:

Q: develop a power point media presentation Presentation will require researching a module specific…

A: To Find:The four different types of reciprocating engines.The overview of the design, construction,…

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.