3. A 20 ohm resistor is connected in series with a coil of inductance 80 mH and negligible resistance. The combined circuit is connected to a 200 V, 50 Hz supply. Calculate (a) the reactance of the coil, (b) the impedance of the circuit in polar form, (c) the current in the circuit, (d) the power factor of the circuit, (e) the power absorbed by the circuit.

3. A 20 ohm resistor is connected in series with a coil of inductance 80 mH and negligible resistance. The combined circuit is connected to a 200 V, 50 Hz supply. Calculate (a) the reactance of the coil, (b) the impedance of the circuit in polar form, (c) the current in the circuit, (d) the power factor of the circuit, (e) the power absorbed by the circuit.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

Use 3 decimal places and box the final answer. A 4-ohm resistor is in series with a 7.96-mH inductor connected across a 110-V 60-Hz source. Determine : a) the impedance b) the input current c) the voltage across the resistor and the inductor d) Draw the phasor diagram showing the current and the voltages. e) The power factor and the power input to the circuit.
A 25-ohm resistor connected in series with a coil of 50-ohm resistance and 150-mH inductance. What is the power factor of the circuit? The standard frequency is 60 Hz. Show complete solution.
3. Two circuit elements in series consume 60 VAR when connected to a 120 – V, 60 – Hz source. If the reactive factor is 0.6, what are the two components and what are their values?
A series circuit consisting of 10 ohm resistance and 60 mH inductance is connected across a 220 volts (RMS) 60 hz supply. Determine the magnitude of the total current in the circuit.
I need an answer in a short time
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
57. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the following a. Total inductance in millihenry b. total current c. reactive power
Please answer question in image with details on how to do it. Thank you.
In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
A sinusoidal voltage with effective value (73 V), and a Frequency its value (80 Hz), was applied on a series circuit that consists of a coil with inductance of value (0.05 H), and a resistor of value (5 N). Calculate: 1. The maximum value of the voltage? 2. The inductive reactance of the coil? 3. The electric impedance of the circuit? 4. The maximum value of the generated current in the circuit? 5. The phase angle? 6. The power factor? 7. The power dissipated inside the coil? 8. Draw a diagram showing the results?
An RL series circuit is connected to a 60-Hz, 208-volt power line. A clamp-on ammeter indicates a current of 18 amperes. The inductor has a reactive power of 1860 VARs. a. Draw the schematic diagram. b. Compute the impedance. c. What is the value of L? d. What is the value of R? e. Find the power factor..
An alternating voltage of 110 volts is applied to a circuit with resistance of 8.66 Ohms, inductance of 0.106 Henries, and capacitance of 75.8 microFarads. The frequency of the voltage is 50 Hz. Determine: a. The current in the circuit and its phase angle relative to the applied voltage. b. The voltage drop across each component of the circuit. c. The active and reactive power inputs to the circuit. d. Draw (Not hand-sketch) the equivalent power triangle. e. Is the RLC load of the circuit inductive or capacitive? Why?