3. A 2" nominal diameter pipe has 1,000 BOPD of oil flowing through it. The pipe ID is 1.988 inches and the oil has a specific gravity of 0.85 and contains 3% CO2. a.) What is the erosional velocity in this pipe? b.) What is the actual velocity of the oil in the pipe? c.) Can this pipe be effectively treated for CO2 and why or why not.

3. A 2" nominal diameter pipe has 1,000 BOPD of oil flowing through it. The pipe ID is 1.988 inches and the oil has a specific gravity of 0.85 and contains 3% CO2. a.) What is the erosional velocity in this pipe? b.) What is the actual velocity of the oil in the pipe? c.) Can this pipe be effectively treated for CO2 and why or why not.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter2: Municipal Solid Waste Characteristics And Quantities

Section: Chapter Questions

Problem 2.9P

See similar textbooks

Similar questions

A pipeline was constructed of a pipe with inside diameter 101 mm and outside diameter 114 mm. On examination it was found that the wall thickness had been reduced by corrosion to about half the original value in 3.25 years. i) Estimate the rate of corrosion in mm per year. A decision has to be made on what material to use to replace the pipe. Three suggestions have been made: ii) Replace with the same schedule carbon steel pipe and accept renewal at 3-year intervals. iii) Replace with a schedule 80 pipe, outside diameter 113 mm, inside diameter 97 mm. iv) Use stainless steel pipe, which will not corrode. The estimated cost of the pipes, per unit length is schedule 40 carbon steel $6, schedule 80 carbon steel $8, stainless steel (304) schedule 40 $26. Installation and fittings for all the materials adds $17.5 per unit length. The downtime required to replace the pipe does not result in a loss of production. If the expected future life of the plant is 8 years, recommend which pipe to…
(a) The following data are collected for a modulus ofrupture test on a refractory brick (refer to Equation6.10 and Figure 6,14):F= 5.0 x 10 N.L= 200 mm,h= 130 mm.h= 80 mm.Calculate the modulus of rUpture: (b) suppose thatyou are given a similar rolracioty with the fallSpensin and same dimensions except that its heightSit ts only 60 mm. What would be the load (F) necesary to break this thinner refractory?
What are Tubular Precipitators?
Explain about the Grouting and injection methods.
7.22 Casing with an ID of 10.05 in. and a strength in tension of 450,000 lbf in the joints and 629,000 lbf in the pipe body is being suspended from the surface while being cemented. If the effective weight of the casing being sup- ported is 240,000 lbf and a safety factor of 1.4 is desired, how much surface pump pressure can be applied safely to displace the cement? The casing burst is rated at 3,130 psi (for zero axial stress). Solve to the nearest correct solution
Plastic pollution - Word res Mailings Review View Help Tell me what you want to c Aa - 令|=、而,。 AaBbCcDc aby . A 1 Normal Paragraph Q1 A) how to change the properties of bitumen using plastic waste? B) use of plastic waste for road construction?
?? please solve B,C and D.... Please answer all..... I don't want single answer.... My request answer all. This is not an assignment question and not a graded question
Write a note on Menard Vacuum Consolidation process.
Mailings Review View Help Tell me what you want AaBbCcD 前, -A- T Norma Paragraph Q1 A) definition plastic waste? B) uses of plastic waste? C) how to change the properties of bitumen using plastic waste? D) use of plastic waste for road construction?
RESEARCH ABOUT THE GROUTING - BULK VOID FILLING. AND ITS APPLICATION AND SAMPLES
what is the effect of alkalinity on flocculation?
A constant velocity grit chamber is used in a small coastal community as a form of pre- treatment to incoming wastewater flows. The town regularly experiences a number of visitors during school holiday periods. If the usual wastewater flow is 10 ML per day, and the usual holiday period flow is 18 ML per day, design an appropriately sized grit chamber arrangement if the target grit has a diameter of 0.16 mm with a specific gravity of 2.75. Show your solutions for the following (but not necessarily in this order): 1. Determine the settling velocity for the target particle 2. Assuming a horizontal flow velocity of 0.32 m/s determine an appropriate overflow rate for the grit chamber 3. Determine an appropriate chamber length and cross sectional area and draw figures 4. Comment on how you could accommodate for the seasonal fluctuations in flows.