3) What is timber seasoning? what are the advantages of timber seasoning  4) what is carriage bolt and its usage?

Q: Question What is the efficiency of joint when strength of bolt per pitch length is 60 KN and…

A: Given- Strength of bolt per pitch length=60 kN, Strength of plate per pitch length=150 kN It is…

Q: match the following

A: Solution:- given following image is,

Q: Give the procedure in Indentation Resistance Test of wood.

A: Brief concept introduction- Indentation Resistance Test of wood- This test is done to determine the…

Q: Distinguish between bearing type connection & friction type connection

A: The objective of the question is to differentiate between two types of connections used in…

Q: QUESTION 2 A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section.…

A:

Q: Problem 5: Hydrostatic Pressure Consider the swimming pool light fixture shown below. It has a…

A: Given data,D=Dia=15cm=0.15mR=radius=mz=depth=2.5mFINDvertical hydrostatic force (N)

Q: Which statement about perforation plates is FALSE? Perforation plate type may help in identification…

A: c. The foraminate perforation plate looks like a ladder is false. A foraminate perforation plate is…

Q: From the above figure, determine the numbe a. 10 x 20 x 40 cm CHB b. Vertical reinforcement spaced…

A: I have solved your problem

Q: In checking the quality of weld, what are the pros and cons of variousnon-destructive weld…

A: Solution: There are basically three common non destructive testing of weld which include: 1.…

Q: draw -for the tread bars - 3-D 10 mm -for teh iser bars- d 10 mm @150 mm o.c. size of wooden…

A: We need to draw the reinforcement details of tread and riser

Q: What are the main types of engineered wood products?

A: Engineering wood are made up of softwood and hardwood with bonded strands, veneers, lumber and other…

Q: 17. Minimum threads/buckles exposed exposed to bolts after nut/s installation 18. Methodology…

A:

Q: how many sheet of plywoodwill be needed to form the decking

A: The requirement of number of plywood sheets  is calculated by dividing the area to be decked by the…

Q: Choose the correct answer Temporary bridges are built from a-Stones b-Steel c-the wood d-Nothing…

A: The temporary bridges are mostly built by using the prefabricated steel girder, steel plates, and…

Q: 1. A center-point bending test was performed on a 2 in x 4 in wood lumber according ASTM D198…

A: Modulus of rupture= MI×yM- Bending moment at maximum load I- Moment of inertia y- maximum distance…

Q: Calculate the maximum allowable load that a nominal 203.2x 203.2 mm (8”x8”) sawn lumber column, 4.0m…

A: When the amount of load is acting on the body or specimen it goes under some amount of deformation.…

Q: What standard is followed in the production of softwood lumber?

A: The Standard that is followed in the production of softwood lumber is: As per the code the standard…

Q: Question 1: For the sawn lumber sizes shown below, identify the one that is classified as "timber"?…

A: Answer  As per American Lumber Standard we have follwing classifications of Lumber. For Boards…

Q: What are relative advantages of plain-sawn and quarter-sawn lumber ?

A: The advantage of quarter- swan lumber are : It swells as wells as shrinks along the width.   It does…

Q: 5) What is the role of the cover on the rebars in reinforced concrete sections? A) Cross-sectional…

A: Covers are use to prevent from the environmental exposure of the bars.

Q: THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH!…

A: Solution: Given: Diameter of rivets = 16 mm Thickness of gusset plate = 20 mm Allowable Bearing…

Q: Please define how Can reinforcing steel be tack welded as an alternative to using wire ties or…

A: 1. It depends on local standards and codes. Much steel is welded into grid patterns for lightweight…

Q: Be aware of the types of many products manufactured from wood?

A: Solution: Types of products that are manufactured from wood are: 1. Bath towel 2. Tooth paste 3.…

Q: Standard dressed sawn lumber with nominal size 12x14 falls into which category? Boards Dimension…

A: Lumber, also known as timber, is wood that has been processed into beams and planks, a stage in the…

Q: What are the main two differences between a pre-tensioning system and an unbonded post- tensioning…

A: In pre-tensioning system, the tendons are pre-stressed before the concrete is poured or hardened.…

Q: Calculate the maximum allowable load that a nominal 177.8 x 177.8 mm (7”x7”) sawn lumber column,…

A:

Q: If a bolt bears on a hole in a sawn timber beam or column, describe how the strength of the…

A: Tensile strength Tensile strength in the direction of the grain is usually 10-20 times more than its…

Q: Please provide complete solution for full credit and box final answer/s. PROBLEM: A two-point…

A:

Q: 4) If a bolt bears on a hole in a sawn timber beam or column, describe how the strength of the…

A: The timber has many characteristics which is suitable in construction purposes. Timbers has high…

Q: One wood product/item which have FIVE different joint connections (L-joint, rabbet, mortise and…

A: The following are the main joints in wood

Q: QUESTION 12 List 2 methods that can be used to protect timber structural systems from termites. For…

A: Following are the two methods that can be used to protect timber from termites in Australia :

Q: What is the efficiency of joint when strength of bolt per pitch length is 60 KN and strength of…

A: Strength of bolt per pitch length is 60 kN, Strength of plate per pitch length is 150 kN.

Q: f structural connection, what are the forces allowed and the forces resisted by the structural…

A: The three most popular types of supports in beams and structures to connect them to their base are…

Q: Summarize the merits of HSFG bolts

A: The objective of the question is to understand the advantages or merits of High Strength Friction…

Q: What considerations should be made when inspecting building structural steel connections for safety…

A: When inspecting building structural steel connections for safety and durability, several key…

Q: Typical means of anchoring a window unit into a masonry wall include: a. Wood nailer strips attached…

A: Wood nailer strips used to create a true plane on which to attach or strap flat surface materials.…

Q: a static centerpoint bending test was performed on a 2x2x30in wood sample according to astm D143…

A: Given- Dimension of wood sample = 2×2×30 inchSpan between supports = 28 inch Maximum load = 600 lb

Q: what is the nominal maximum load capacity of a grade 60 reinforcing bar with a diameter of 20 mm?

A:

Q: 7.Wood planks used for scaffolding must: be multi-grained and free from splits, rotted areas or…

A: