3) The controlled variable (y) and the manipulated variable (u) change with time (t) of a process are given in this table. 田 u y a) Calculate the dead time, K (gain), and t (time constant) 0 3 2 3 values and write the transfer function of the process. 4 b) Write down the transfer function of a PID control system 6 3 3 applied to this process by using the following equations of Cohen-Coon method. 10 12 3 14 3 16 3 1,63 18 3 2,97 20 4,06 22 3 4,96 24 5,69 26 3 6,29 28 6,78 30 7,18 32 3 7,51 34 7,78 36 3 8,0 38 3 8,25 40 8,50 45 3 8,72 50 3 8,89 100 3 8,99 olo 3. 3. 3. 3. 3. 3. 3. 3.

3) The controlled variable (y) and the manipulated variable (u) change with time (t) of a process are given in this table. 田 u y a) Calculate the dead time, K (gain), and t (time constant) 0 3 2 3 values and write the transfer function of the process. 4 b) Write down the transfer function of a PID control system 6 3 3 applied to this process by using the following equations of Cohen-Coon method. 10 12 3 14 3 16 3 1,63 18 3 2,97 20 4,06 22 3 4,96 24 5,69 26 3 6,29 28 6,78 30 7,18 32 3 7,51 34 7,78 36 3 8,0 38 3 8,25 40 8,50 45 3 8,72 50 3 8,89 100 3 8,99 olo 3. 3. 3. 3. 3. 3. 3. 3.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1(a): Check the convergence of the series [ In(1+) by finding (if any) it's 'nth; partias n=1 72 (b)Test the convergence of the series: Σαν", n=1 sum. (-1)" 00 Σ sech n, n=1 n In n I need a full and correct handwritten solution by the expert.
Q4) Channel 1 of a two-channel system handles (0-3) kHz signals; the second channel handles (0-5) kHz signals. The two channels are sampled at equal intervals of time using very narrow pulses at the lowest frequency that is theoretically adequate. Find (a) The minimum sampling frequency to recover both signals, (b)Tx (c) The bandwidth of the time multiplexed signal.
I dont give chatgpt answer
(b) Aliasing is an effect that causes different signals to become indistinguishable when sampled. (i) Explain this aliasing effect with an illustration. (ii) Also suggest any two measures to avoid this aliasing effect.
• Discussion : 1. Why Continuous Time signals are represented by samples? 2. What is meant by sampling? 3. State Sampling theorem. 4. Explain the working principle of sample and hold circuit. 5. What is the significance of using sample and hold circuit?
4. An analog signal x(t) with maximum frequency f = 400 Hz, is passed through an analog-to-digital. converter (A/D) with sampling rate fnvquist, and quantization level L=8. What is the speed of the A/D in bits/sec?
12 - When the unit step function is applied to the input of the control system given below, the peak time of the output signal is 0.59 s and the settlement time is 0.88 s. It is also known that the steady state error of the system is 10% for the same input. So what is the unknown K2 value in the transfer function? calculate.A) 5.7B) 4.9C) 3.7D) 7.3E) 6.4
3. Design a-full subtractor with two multiplexers (MUXS) S(xy.2) = E( ...), C(x.y.2) = E(... ). Connect the variable z to the data inputs. Connect the variables x and y to the selection inputs.
2. A singer voice is sampled for 4 second by an 8-bit ADC at a sampling frequency of 10 kHz. The samples are stored on a memory chip. What is the minimum memory size both in [bits and bytes] required to store all the samples? ii. How long the signal must be sampled to store the samples in 100Mbytes CD- ROM iii. What should be the highest frequency component of the signal? iv.If sampling frequency is doubled then how long the signal must be sampled to store samples in 100Mbytes CD-ROM
1.3.Linear systems with random inputs. 1.3.1.1.3.1. Responses of linear systems to random signals. 1.3.2.1.3.2. Spectral characteristics of the system response. 1.3.3.1.3.3. Process sampling.
Problem 2. Consider the LTI system defined as y[n] = 0.5y[n–1]+2x[n]+ x[n–1] Q1. Is the system stable? Causal? Q2. Determine the output signal y[n] when then the input is x[n]=u[-n]with u[n] the unit step sequence. (Recall: write the input sequence as the sum of a causal plus an anticausal sequence)
Consider the digital control system shown below. Plot the root loci as the gain K is varied from 0 to infinity. Determine the critical value of gain K. for stability. Assume that the sampling period is 0.1 sec. What value of gain K will yield a damping ratio of the closed loop poles equal to 0.5. R(2) K(z + 1) (2-1)(z- 0 6065) C{z}