3 The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm (X is a last digit of your matrix number) and is used as a strut to support the beam. The yield strength of material is oy = 260 MPa. Take modulus of elasticity, E, = 210 GPa. (a) Determine the maximum intensity w of the uniform distributed load that can be applied to the beam without causing the strut to buckle. Take factor of safety = 3 against buckling. Check whether Euler's equation is appropriate or not. (b) Then, calculate the new maximum intensity w if end condition for strut both fixed.

3 The A-36 steel rod BC as shown in Figure Q3 has a diameter of 5X mm (X is a last digit of your matrix number) and is used as a strut to support the beam. The yield strength of material is oy = 260 MPa. Take modulus of elasticity, E, = 210 GPa. (a) Determine the maximum intensity w of the uniform distributed load that can be applied to the beam without causing the strut to buckle. Take factor of safety = 3 against buckling. Check whether Euler's equation is appropriate or not. (b) Then, calculate the new maximum intensity w if end condition for strut both fixed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 1. Simplify the following expressions (note that 8, is the Kronecker delta, repeated index means summation, and comma represents derivative). (a) Sim Smp Sap (b) ▼ Skmum,n (c) ▼ x 8kmui,mk
HCM-6 At the design speed Vo Dan's car can go around a banked curve of radius 150M and banking angle of 10.0° without any friction force. The car is shown as viewed from behind in the figure below. R=150m 10.0° a) Use the figure above to draw the free body diagram for the car. Also show on the FBD the direction of the car's acceleration and show coordinate axis directions. b) Write down newtons's second law in component form for the car. Use NO numbers for this part. c) Use your equations from step b) to find the design speed Vo.
1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
in typing form
I need it quickly please
Find the acceleration of the specified object. (Hint: Recall that if a variable is changing at a constant rate, its acceleration is zero.) A boat is pulled into a dock by means of a winch 16 feet above the deck of the boat (see figure). The winch pulls in rope at a rate of 7 feet per second. Find the acceleration of the boat when there is a total of 20 feet of rope out. (Round your answer to three decimal places.) ft/sec² Need Help? Read It Not drawn to scale
In the figure shown, |=140mm, b=40mm and wAB=1100rpm (clockwise) Solve for (a) the velocity(m/s) of P when 8=65° (0) the angular velocity(rad/s) of BD when e=65". (Note: WaB is constant) T-od
In the figure shown Hk is the same for point A and B. What is the acceleration(m/s) of the block in point B, 15° from the horizontal? A a= 4.8 m/s 30 B 15 Select the correct response(s): 1.53 0.4143 2.09 1.31 2.42 1.75 O 0,9719
The acceleration of A is 1.8 m/s downward and the acceleration of Cis 2.4 m/s² upward. Find the acceleration of B. The acceleration of B is positive if downward, negative if upward. C B A Part 1 Write an expression for the length of the rope. B A Answer: L= SA+ Sg+ sc+ constants
Ex/ Given AB =DE = 150 mm, BC = CD = 450 mm, EF = 375 mm and NgA = 120 rpm. Find (a) velocity of F and (b) angular .velocity of DC %3D
For a 10 H7/p6 fit