3- Plakasında 600 V, 50 Hz, 18 kW, 1450 devir/dakika yazan 3 fazlı, yıldız (Y) bağlı, 4 kutuplu asenkron motorun, tam yükte (anma yükünde) şebekeden çektiği hat akımı 30 A'dir. Motorun tam yükte güç faktörü 0,8 (geri)'dir. Motorun tam yük durumu için, aktif giriş gücünü (P), reaktif giriş gücünü (Q), verimini (u) ve kayma (s) değerlerini bulunuz. Bulduğunuz sonuçları aşağıdaki kutulara yazınız. (A 3 phase, Y connected induction motor which has 4 poles, has plate values a3, 600 V, 50 Hz, 18kW, 1450 rpm and has a line current value of 30 A at rated load (full load or nominal load). The power factor is 0,8 (lagging) for rated load conditions. Find the input active power (P), input reactive power (Q), efficiency (u) and slip (s) values of the motor at rated load conditions. Write the answers inside the boxes below.)

3- Plakasında 600 V, 50 Hz, 18 kW, 1450 devir/dakika yazan 3 fazlı, yıldız (Y) bağlı, 4 kutuplu asenkron motorun, tam yükte (anma yükünde) şebekeden çektiği hat akımı 30 A'dir. Motorun tam yükte güç faktörü 0,8 (geri)'dir. Motorun tam yük durumu için, aktif giriş gücünü (P), reaktif giriş gücünü (Q), verimini (u) ve kayma (s) değerlerini bulunuz. Bulduğunuz sonuçları aşağıdaki kutulara yazınız. (A 3 phase, Y connected induction motor which has 4 poles, has plate values a3, 600 V, 50 Hz, 18kW, 1450 rpm and has a line current value of 30 A at rated load (full load or nominal load). The power factor is 0,8 (lagging) for rated load conditions. Find the input active power (P), input reactive power (Q), efficiency (u) and slip (s) values of the motor at rated load conditions. Write the answers inside the boxes below.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An inductive load of 100 Ohm and 200mH connected in series to thyristor supplied by 200V dc source. The latching current of a thyristor is 45ma.and the duration of the firing pulse is 50us where the input supply voltage is 200V. Will the thyristor get fired?
The Insulator has a very small energy gap ? True O False O
The single-phase half wave rectifier is suppling an (RL) load. Assume that power is equal to 1500 , where R=3Ω, a=π/6 and β=2π/3. find maximum voltage.
please explain the principle behind rerfractometer and salometer.
If a resistive load is supplied from a single phase half wave rectifier , if a supply voltage is (230v) calculate Vout at firing angle (a =120o) and draw the input and output waveform .
Is it possible to detect maximum or peak AC voltage with an analog voltmeter? How about a digital voltmeter
The Insulator has a very small energy gap ? True O False O
To control a purely resistive load by a thyristor, the range of the firing angle in degrees must be:
Indicate the functional elements of the following measuring devices shown in Figure
The primary voltage on the transformer in Figure 2–46 (p. 96) is 120 V rms and NP : NS = 15:1. Diode voltage drops are 0.7 V. (a) What should be the value of RL if the average current in RL must be 0.5 A? (d) Is it alright to measure with an oscilloscope both the input and output waveforms at the same time in Figure 2-46? Why or why not?
What do you thinkresistance is an important property in the field of electronics and electricity?
List the different factors which determine the output from a wind energy converter