3 P2 =5.2 (Figure 1) Set P1 = Determine the force in member AB, and 3 state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the E 6 m case of tension. Part B D Determine the force in member AE, and B state if the member is in tension or 4 m 4 m 4 m compression. Part C P2 Determine the force in member BC, and state if the member is in tension or compression. Part D Determine the force in member BE, and state if the member is in tension or compression. Part E Determine the force in member CD, and state if the member is in tension or compression. Part F Determine the force in member CE, and state if the member is in tension or compression. Part G Determine the force in member DE, and state if the member is in tension or compression.

Q: For the pair of 26-lb forces applied to the handles of the crimper tool, determine the crimping…

A:

Q: At what angle theta will both boxes begin to slide.

A: m1=65lbs = m2

Q: Q1 -B- Draw just the Free Body Diagram of the following figures. 30 kN/m Fig. (2) -3 m- +-3m- -3m-…

A: given; draw free body diagram for given figure;

Q: 70 400N 300N Figure (1)

A: Force is a vector quantity that has both magnitude and vector to signify its value. So, to get the…

Q: *2-4. The vertical force F acts downward at A on the two- membered frame. Determine the magnitudes…

A:

Q: Little Oliver is trying to help his parents with their garden using his new tiller with a height of…

A: Given Data d1=8cm=0.08m d2=9cm =0.09m θ=30° M=9N.m

Q: The magnitude of the coordinate direction angle with y axis of force F1 equals to;

A: Given data  Given figure

Q: The screw eye in Fig. 2-1la is subjected to two forces, F, and F.. Determine the magnitude and…

A: Given Data F1=100 N F2=150 N

Q: Solve for A and B. P=400 lbs. 0=30° P 45° B www Drawing not to scale. Use given angles. Magnitude of…

A:

Q: Determine the design angle 0° ≤ ≤ 90° between members AB and AC up to the right, in the direction…

A:

Q: The screw eye in Fig. 2-11a is subjected to two forces, F, and F. Determine the magnitude and…

A:

Q: Q) Consider a weight supported by a cable as shown in figure below is equal 100 kN. Determine the…

A: W=100 kN

Q: H G 60 E D 7 kN 7 kN 9 kN 6m 6m 6m 6m

A:

Q: 1. Determine the eccentricity and location (indicate your reference force) of the force on the…

A:

Q: Determine the magnitude and direction of each force. In the figure shown, a=7 in and F= 100 Ibf.…

A:

Q: 5. A cylinder having a mass of 250 kg is to be supported by the cord which wraps over the pipe.…

A:

Q: internal normal for

A: introduction: here we have to find out largest internal force

Q: Two forces X and Y act vertically downward directly at points D and F respectively while force Z…

A: Given data as per question  X=553N Y=248N Z=122N a=5.7m  b=3.6m…

Q: F = 500 lb Determine the components ofF, and F, in x-y and x’-y’ systems 25 450 30 F2 = 750 lb

A:

Q: ) Determine the total magnitude of force, ΣFy acting in y-direction ( answer in newton, N with two…

A:

Q: The horizontal and vertical components of several forces are: (a) Ph = -200 lb and F=-200 lb; (c)…

A:

Q: The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as…

A:

Q: For the distributed load shown below, determine the equivalent force's magnitude and location,…

A: Given data: a=0.312 KN/m2b=1.08  KN/m2L=3.46 mw=(-ax2+bx)  KN/m

Q: Determine the force in cored AB 30° A В 800 lb/ft -15 ft- -15 ft Your answer

A:

Q: Q2: Replace the 100 Ib f Force of Figure below into horizontal and vertical components for each of…

A: Given:F=120 lbθ1=350θ2=900θ3=1600θ4=2000

Q: The frame shown supports a crate that weighs W = 250 lb. Knowing that L = 1.1 ft, determine the…

A: According to the given dataW=250 lb L=1.1 ftr=0.4 ftWe need to findInternal force N,V and M at…

Q: (NOT IN SCALE) Determine the direction of angles of a force vector F, where 01 = 25°, 02 = 45°, and…

A: