3) if the applied force F2= 0 kN, the maximum force that any member can support is 6.3 kN in tension and 11.7 kN in compression, determine the maximum force F that can be supported at joint D. Please pay attention: the numbers may change since the are randomized. Your answer must include 1 place after the decimal point and proper

Q: Part of the screw thread connecting the adjacent flank on top of the screw thread is known as O…

A: Correct answer is option (b) Pitch  The pitch of a thread is the distance measured parallel to its…

Q: 25. ..s) Two circles, each of radius r, have their centers located at (0,2) and (0,3). Each is used…

A: As per honor code and answering guidelines I can  answer 1st question at a time.If you want other…

Q: y

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: Nut 17.0 N 37° 25.0 cm

A: The text provides the following information:The force applied to the wrench is 17.0 NThe distance…

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: X 300 mm D 800 mm B

A:

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: 3

A:

Q: The distance between the corresponding point on the screw thread when measured parallel to the axis…

A: Create:  It is the peak edge of a screw thread, that connects the adjacent flanks at the top. Flank:…

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: What is the Neutral Axis?

A: The neutral axis is the fiber of the beam with no normal stress. When a beam is subjected to a…

Q: b) Determine the March number of the bullet for both medium.

A: (b) Consider the helium gas and calculate the speed of sound in helium. cHe=γRTMFor γ,…

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: R D.

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise   and the figure  We need to find Force F to…

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: 3 ft us 4 ft < 1 of 1 B Determine the moment of the force F = {40i -35j + 20k} lb about the AB ax…

A:

Q: what is the actual area in part a ?

A: Given: Q=5000 m3/min=5000m3min×1min60 sec=83.33 m3/s V=6.0 cm/s=6.0cms×1m100cm=0.06 m/s

Q: For machine element, locate the centeroid

A: Answer:  Centroid ( 44.78 , 27.19 , 26.25 ) For a step-by-step solution have a look through the…