3- For the network shown in figure below: a) Determine VL, IL, Iz, and Ir for RL = 180 2 b) Repeat part (a) if Rµ = 470 Q. c) Determine the value of RL that will establish maximum power conditions for the Zener diode. VR d) Determine the minimum value of RL to ensure that the Zener diode is in the "on" R=220 2 + state. 20 V Vz = 10 V RL VL PZM = 400 mW

3- For the network shown in figure below: a) Determine VL, IL, Iz, and Ir for RL = 180 2 b) Repeat part (a) if Rµ = 470 Q. c) Determine the value of RL that will establish maximum power conditions for the Zener diode. VR d) Determine the minimum value of RL to ensure that the Zener diode is in the "on" R=220 2 + state. 20 V Vz = 10 V RL VL PZM = 400 mW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

diode? Under what circumstances does the output voltage remain constant in a limiter circuit with Zener When does the Z-current Iz begin to flow? Under what circumstances is the limiting effect maintained even under load?
3. A Si pn junction is operating in forward bias. Determine the increase in forward bias voltage that will cause a factor of 100 increase in the diode current. Take T= 300 °K.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Solution of this question is required. Urgently please.
3) With reference to the illustration given below, with detailed explanation discuss about the reverse recovery time and its significance. Current through diode I before reversed Current through diode after reverse biased biased Reverse recovery K time rr Time rm = Reverse maximum Irm Slow Recovery current
1. The reverse-saturation current of a pn junction diode is Is = 10-¹¹ A. Determine the diode current for diode voltages of 0.3, 0.5, 0.7, -0.02, -0.2, and -2V at T=300K.
If Vz=6.2V and Pzmax=150mW. i) Determine the minimum value of RL to ensure the Zener diode is in the On state ii) Find the value of RL that will active the maximum power condition of the Zener diode R 470 N VIN 24 V RL
1. Determine the minimum voltage required for regulation to be established in the circuit below. Use an ideal Zener diode with V₂=14V at Izr=30mA. VIN R www 560 12
5. Draw the Input/Output Vin/ Vout characteristic curve of the circuit given below. However, assume a Constant Voltage Diode Model and VB = 2 V. D₁ R₁ W VB MI D₂ R₂ Vout
There are two LEDs that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the “on” diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V
In a single phase half wave controlled rectifier with inductive load without freewheeling diode, the output voltage is zero during the wt=t to 2rt. Select one: O True O False
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps