3) For the fiqure shunen, what should be the minimum diameter of the rivets attached as shoun if the allowable axial sfress is 6O MPO and the allowable shearing strers is ito MPa? -- 1 mw

Q: 2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: The weight of the box can be found by multiplying its mass by the acceleration due to gravity. Since…

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Which of the following statement is incorrect? Select one: O Friction is high for dry surface O…

A:

Q: If A = Gax + 3a, and B = 8'ax + 2ay-8 az, %3D (a) find the dot product (b) find OAR

A: GivenA→=6i^+0j^+3k^andB→=8i^+2j^-8k^

Q: solutions are given, please resolve to get these solutions

A:

Q: 4. The surface temperature of the hot side of the furnace wall is 1200 degrees C. It is desired to…

A:

Q: A pressure cylinder has an outer diameter 210 mm, internal pressure 4.4 MPa, and maximum allowable…

A: Given Data

Q: Suppose that A24 . Eaun) • Part C Determine the coordinate direction angie of the resutant force of…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: can you make a sketch of the solution

A:

Q: 4. Consider a situation similar to that in Experiment 2. Given the following distances traveled…

A: In the question, it is asked about average velocity. Average velocity can be calculated the total…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: 1500 liters/s of ammonia gas at 100°F and pressure of 30 in.Hg has a specific heat ratio of 1.304.…

A: Given data Q=1.5 m3/sT1=100°FT2=180°Fγ=1.304 Here, Q is the flow rate and T1 is the initial…

Q: A hemispherical dome of radius 40 feet is to be given 5 coats of paint, each of which is 1/100 inch…

A: Initial radius of the hemispherical domeThickness of the each coat of paint

Q: 1. Given the following measurements (in metric and English respectively) of a metal cylinder: length…

A: as you mentioned I solved 1st. one. For solution refer below images.

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: Please show detailed solution in a handwritten format. Don't use chatgpt. Torque and Maximum shear…

A: Step 1: Step 2: Step 3: Step 4:

Q: A diesel engine in a power plant has an output of 150 KW at 260 rpm. It uses fuel oil having a…

A: Given data: Diesel engine power output = 150 kW @ 260 rpm Calorific Value of Fuel oil = 43912 kJ/kg…

Q: For question 2, name the method to form that shape and name the cut out process. For question 3,…

A: Solution:

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: Write the equation to calculate the work done by an axial force?

A: Work: Work is defined as the multiplication of the axial force on the body and displacement…

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: B 20 mm- 50 mm A 20 mm 100 mm 50 mm 100 mm M = 8 kN-m

A:

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: oy. Suppose the vessel is subjected to uniform intemal pressure p, determine the minimum thickness…

A:

Q: 3. From N-S equation, derive the kinetic energy equation of E = u₁u₁/2. Following the kineti energy…

A: Given: Initial velocity =ui We have to find out the kinetic energy equation from newtons second law…

Q: 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is…

A: Given Solution is  Incorrect . Because formula used are not completely correct.

Q: Using the Milling machine with DRO create a hallow that suites the shape of the given MILD STEEL

A: given; Using the Milling machine with DRO create a hallow that suites the shape of the given MILD…

Q: Please give the details explanation of the answer

A:

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: How did you get the temperature 367? What is the solution?

A:

Q: That is the answer I have and it is marked as wrong, could you please do it again and see if you get…

A:

Q: Give a steps by steps answer of the solution

A:

Q: Find the centroid Y of unsymmetrical I- section shown below with respect to its base

A: Solution:

Q: What is the max circularity, on a radius, on the part below before a feature control frame is…

A: The tolerance of the part is

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.