3- Consider the following 1D reservoir, where steady state, single phase oil flow takes place. This reservoir has homogenous property distribution of F =25% and k=18md. Figure below shows the uniform dimensions of the finite difference blocks. The boundary conditions at extreme ends are no flow. Well in grid block 4 produces at a rate of 3500 STB/D. Obtain pressures of each blocks. Also note that m=20 cp, B=1, c=. 9sc=-150 STB/D 1,000 ft 75 ft 1,000 ft P=3000 psia P=4000 psia b=0.001127, a=5.615

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: Suppose that the length of the steel bar is measured by a number of different observers and…

A:

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Is this the only correct option in the question above? I think the question is worded for more than…

A: To elaborate why a sling psychrometer can measure humidity.

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: Please need help. Clear explanation or answer. Use the picture to answer 1,2,3,4, 1- The direction…

A:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: What is the moment's function?

A: Moment deals with the physical quantities situated at some distance relative to the reference point.…

Q: 48, As preparation for this problem, review Example 13. Sup- pose that the pilot suddenly jettisons…

A: Solution for problem 48: Given data: Weight of the plane initially, W=86500 N. Let 'T', 'L', 'R' be…

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: It is a tool made from hexagon or octagon-shaped tool steel, one end is shaped for the cutting…

A: Screw driver is the tool which has a holding part made of non conductor and another end is shaped…

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Q: Part II. Longer problem focused on problem solving multiple steps. This problem will be graded based…

A: Step 1: Step 2: Step 3:don't forget to upvote :) thank you and comment if doubt exists Step 4:

Q: part ii

A:

Q: ) Newton's Law of Universal Gravitation states that the force exerted between 2 objects, called a…

A: Data given-  F = G m1m2 / r2

Q: Part I. Shorter problems focused on the fundamentals a. For the image at the right, the coordinate…

A: Step 1: Use definition of dot product to find angle between two vectors.A⋅B=∣A∣∣B∣cosθWhere the…

Q: The algebraic sum of moments of the forces forming couple about any point in their plane is * a.…

A: As per policy,I have solved first three questions .

Q: I find part 2 and 3? Thank you.

A: As Implied, students is clear to get analytical result from the method of intrgration of the…

Q: One end of rod OB is fixed on the wall and the other end is connected to a rigid link structure.…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.